DIRECTIONS: For each of the following photos, draw the “floor plan" that would be used to create in

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: draw any plan using 3x1.5x2.4m

A:

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: A drawing environment in which menus, toolbars, and palets, and ribbon panels are displayed for a…

A: A drawing environment in which menus, toolbars, and pallet, and ribbon panels are displayed for a…

Q: Draw the (Front, Side and Top Views) for the following Figure. R40 140 100 128 160 Front

A: Data given Asked Draw the front view, Side view and Top view

Q: Differentiate between BIM and 3DModeling?

A:

Q: see the photo attached

A:

Q: Draw the grid diagrams for the table below

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: Top View of the given object is as shown below.

Q: top view drawing

A: In top view we see the object from top. Here dotted line represents a cut inside the object.

Q: Complete the profile level notes, perform the customary arithmetic check. Please provide a detailed…

A:

Q: 02: What is architectural drawing? Explain different views of a drawing.   Sir, please explain the…

A: Architectural drawings are the drawings that include technical data of the structural design of a…

Q: show a working plan drawing that is related to civil engineering

A:

Q: 4. How many layers are needed in creating floor plans? D

A: Layers are used for grouping similar types of geometry together so that it can be viewed easily…

Q: Draw the front and top and side view for these?

A: For any object which is needed to be constructed or manufactured it is important to have drawings…

Q: Find the correct front view for the drawing given below.

A: i drawn a rough sketch of ront view   see it in below step

Q: : State the commands used to draw the following GROUND FLOOR PLAN FIRST FLOOR PLAN LEFT ELEVATION…

A: Assuming that drawing has been drawn in AutoCAD, following are the commands would have been used :-…

Q: answer the questions in the attached photo.

A:

Q: What finished surfaces are available when selecting chalkboards?

A: The finish surfaces is based on material or paint we used for surfacing. there are certain options…

Q: Measure the red line using the given figures (please answer in appropriate format for the type of…

A: Let’s take the architect scale as follows:

Q: With

A:

Q: can you show detailed steps?

A:

Q: SKETCH FRONT, TOP ,AND R.SIDE VIEWS

A: NOTE : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: Give 7 materials (for walls) Do materials composition and technical specifications only

A: The seven materials for wall construction are 1. wood 2. Concrete 3. Stones 4. Ceramic Tiles 5.…

Q: A preliminary drawing which is typically hand drawn, with measurements of all the locations of items…

A: Brief concept- Surveying of any location includes drawings, sketches, and preliminary data…

Q: Compute an actual dimension of a distance if the given drawing measurement in the plan is 28 cm…

A: Map scale  A distance on a map and its corresponding distance on the planet are related by a scale.…

Q: If all lines on a drawing are the same thickness, how can walls and partitions, for example,…

A: Engineering drawing shows the plans, cross sections  elevation etc of any structure.  The…

Q: Top, Front and Side view of this sketch.

A:

Q: Draw a graph that represents each floor plan. Use vertices to represent the rooms and outside area…

A: Consider the following circuit diagram. The above circuit diagram represents the floor plan. Here,…

Q: What is an Elevatio Plan? Give its types as well. How do you draft floor & Elevation plans?

A:

Q: Define the terms Streamlines, Streaklines, Stream tube?

A: Streamlines Streamlines are a family of curves that are outright tangent to the velocity vector of…

Q: If all lines on a drawing are the same thickness, how can walls and partitions, for example, be…

A: Object lines are used to establish the outline and distinctive features of components of the…

Q: 5. For each section below, identify each

A: Given:- To identify each element and indicate whether it is stiffened or unstiffened.

Q: Sketch an ISOMETRIC DRAWING from the attached orthographic projection. Follow the assigned…

A:

Q: prepare and submit a 3D isometric projection drawing based on the 2D Multiview object drawing (Top,…

A: Isomeric view in shaded region  It was so tough to imagine

Q: What is the difference between oblique, isometric, orthographic, elevation, plan, and section…

A: Drawings are a commonly used mode of communication in the engineering industry,  As such drawing is…

Q: 5. Draw a diagonal scale 1:1000 to show 1.5 meter. Show a distance of 25.5 meters on it.

A: First to find length of scale

Q: summary about deep drawing? charactaristics

A: Deep drawing is a sheet metal forming technique in which a sheet metal blank is mechanically drawn…

Q: Q2: Use commands (line, arc, rectangle, mtext), then List all required commands to draw the…

A: Required command to draw above dish Rectangle command to draw inner and outer rectangles Arc…

Q: am or drawin

A: From A to B :vB2=vA2+2a1s1402=0+2(4)(s1)s1=200ftFrom C to B…

Q: lustrate a simple work plan drawing related to water resources engineering.

A: Explanation- The Water resources engineering is the field that is largely responsible for water and…

Q: Make a quick isometric sketch from the given views. No need to scale. What to use: Pen & Letter Size…

A: To get the isometric view from the given orthographic projections. First draw two lines…

Q: a) Draw the plan and elevation of the below given line plan. ASsume all data. Toilet 3X2 Bed room…

A:

Q: Adopt appropriate scale to draw the structure drawing of residential plot having dimension of 40*90…

A:

Q: To print the entire project, you will choose to regulate what to plot Display Window Limits Extends

A: A multiple choice questions is asked, please refer step 2 for detailed explanation and solution.

Q: prepare and submit a 3D isometric projection drawing based on the 2D Multiview object drawing (Top,…

A:

Q: Drawing a house plan using Auto0CAD Drawing using the Offset tool

A: Offset is a very good function in Autocad that helps to draw the lines of the wall or any parallel…

Q: What additional information could you add to a sketch to provide other team members with a more…

A: Given What additional information could you add to a sketch to provide other team members with a…

Q: What is the proper procedure to place a text callout on a detail view? O Use MTEXT command and draw…

A: To Determine Which command is used in CAD software to place a text callout on a detail view.