differential equations A circuit with a 10 ohm resistor and a 4.6 henry inductor is connected in series to a 12 volt source. If the initial current in the inductor is 0.5 amps, determine the value of the current after a very long time has elapsed. determine the value of the current after a very long time has elapsed.

differential equations A circuit with a 10 ohm resistor and a 4.6 henry inductor is connected in series to a 12 volt source. If the initial current in the inductor is 0.5 amps, determine the value of the current after a very long time has elapsed. determine the value of the current after a very long time has elapsed.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
In the diagram below, the switch S has been closed for a long time. A) What is the output voltage Vout? What is the charge on the capacitor? b) The switch is opened, so the output voltage increases. What is the time constant that describes the charging of the capacitor in terms of R and C? c) When Vout reaches 10 V, the switch closes and the capacitor begins to discharge. What is the time constant that describes the discharging in terms of R and C? Hint: Apply Kirchhoff's Rules to both loops and the sum of the currents at the junction above the capacitor in the diagram, and use I=dq/dt. If the switch opens when Vout reaches a lower value, say 5V, the capacitor will charge again, and thus one can cycle the voltage with a time constant determined by the circuit: this demonstrates the principle of operation of an electronic timer. 4R S 15 V Vout R
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
The magnitude of the voltage applied to the electrodes of a welding machine can be adjusted in the circuit below. In the range of minimum and maximum value that variable value resistor can take What is the time interval that the capacitor will charge from 0 to 8 V?
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Full-wave 50 Hz sinusoidal controlled rectifier circuit with a peak voltage value of 100 and a source inductance of 8mH is feeding a highly inductive load of 8A. At a firing angle of 60 , the average value of the output voltage and power delivered are, respectively: Power Electronics
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor and a capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor, 48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor. Find (a) the combined copper and iron losses in the inductor (b) the applied voltage.
Half-wave 50Hz sinusoidal uncontrolled rectifier circuit with a peak voltage value of 100V and a source inductance of 8mH is feeding a highly inductive load of 8A. The average value of the output voltage and power delivered are, respectively and what is the communication angle (u) Power Electronics
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor anda capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor,48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor.Find (a) the combined copper and iron losses in the inductor (b) the applied voltage Answer: [(a) 3.3 W (b) 56 V]
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor anda capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor,48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor.Find (a) the combined copper and iron losses in the inductor (b) the applied voltage.Answer: [(a) 3.3 W (b) 56 V] Note: Please provide a clear solution!