DI01) D102) 150- 600 (NOTE: TT shows the continuity of the slab edge ) 1. Determine the design moments of each slab. (Note: You should write the sign for the positive and negative moments). Concrete : C30 • Steel: S420 • Beams : 30x60 cm • Columns:30x50 cm, 50x30 cm • Column height: 3 m • All units in the figure are given in cm • Assume that 10 kN=1 t • Thickness of the slab: 18 cm • Additional dead load : 2 kN/m? • Live load: 4 kN/m? • Unit weight of reinforced concrete: 25 kN/m • Reinforcement bar: Ø8 Rust cover for slab: 20 mm

DI01) D102) 150- 600 (NOTE: TT shows the continuity of the slab edge ) 1. Determine the design moments of each slab. (Note: You should write the sign for the positive and negative moments). Concrete : C30 • Steel: S420 • Beams : 30x60 cm • Columns:30x50 cm, 50x30 cm • Column height: 3 m • All units in the figure are given in cm • Assume that 10 kN=1 t • Thickness of the slab: 18 cm • Additional dead load : 2 kN/m? • Live load: 4 kN/m? • Unit weight of reinforced concrete: 25 kN/m • Reinforcement bar: Ø8 Rust cover for slab: 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

d C
Q1/ Member B is subjected to a compressive force of 10 kips. If A and B are both 0.5 in. thick and made of a material with the shear stress-strain diagram shown below. Determine the smallest dimension a in order to prevent shear failure. Use a factor of safety of F.S. = 5.0 £s. Th (ksi) A y (rad) 90- 80 70 60 50 40 30 20 10 Ofpl = 0.008 Y = 0.54 0.73
Beam ABCD carries a concentrated load and uniformly distributed load as shown below. Draw the shear and moment diagram of the given beam. Show your solution.
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
Determine principal stress
Calculate the design moment strength of a reinforced concrete beam 200 mm x 460 mm if at failure the concrete compression strain is 0.003 and the tensile steel strain is 0.005. The flexure bars are 16 mm in diameter enclosed by 10 mm stirrups. Use f'c = 22 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.
For the given cross section below, Compute tne meximum stress of concrete and steel. All aimensions are in 'mm'. Use M-150KN-m ana n=8. Tne answers are | MPa ana MPa. 500 200 100 400 3-32mm Ø 100 100 10) 100
2- For the cross section shown: i) determine the cracked moment of inertia (ler) using n=8, and ii) using transformed-area method determine stresses in concrete and steel if subjected to a moment M = 150 ft-kips. As = 4.1 in ² Assume f. = 4,000 psi, and f, 60,000 psi. 14"-wide hole As 20" e 6 3* 60 13
A rectangular concrete beam measures 300 mm wide and has an effective depth of 450 mm. Compression steel consisting of two No.22 bars is located 60 mm from the compression face of the beam. If f= 35 MPa and fy = 420 MPa, what is the design moment capacity of the beam for the tensile steel area As = four No. 36 bars in two layers? Provide material properties for concrete and reinforcing steel used in your design.
FOR THE GIVEN PROPERTIES DESIGN d': 15 mm THE REINFORCEMENT OF : 400 mm b d = $80 mm fc = 33 MPa fy = 320 MPa Mu: 1 000 000 000 N mm A. USE B.USE OF NSCP 2001 NSCP 2015 BEAM THE BEAM 132 13 Gra mm of BELOW. #H 1606 210135 03 M 12437 P0122399/100mA 02338941 242