Determine the x- and y- coordinates of the centroid of the shaded aera.

Q: a- What is the required temperature to start the laser action and generate the laser beam, assuming…

A: Given   Wavelength = 5500 A = 0.55 micro meters Find  Temperature, T      Weins law is used to…

Q: What is the pressure difference between points A and B?

A: It is given that  Relative density of oil S= 0.85 Density of water = 1000 kg/m3 density of…

Q: The specific heat in kj / kg. C for a crude fraction with Specific gravity of 0.819 at 55.6 C is

A: Write the given data. SG=0.819T=55.6 °C

Q: We can say that a beam is in equilibrium, if all forces and moments applied to it are equal .zero…

A: Explanation: According to conditioning of equilibrium of a beam, The sum of all the forces in X…

Q: B- A three-lobe rotary positive-displacement pump moves 0.45 cm³ of blood in each lobe volume Vlobe.…

A:

Q: RT B- Find an expression for Cp - Cv if the equation of state is p =- v-b for an ideal gas 34 - and…

A:

Q: Molybdenum has a BCC crystal structure, an atomic radius of 0.1363 nm, and an atomic weight of 95.94…

A:

Q: 4Q. Compute the capillary depression of mercury at 68 °F (0 = 140°) to be expected in a 0.05 in…

A: Given:   Temperature of mercury, T=68 deg F Angle, Q=140 deg Diameter of the tube, d=0.05 in

Q: What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 1 inches? The…

A:

Q: * For the multi shapes, the moment of inertia is................... to the algebraic sum of the…

A: Given question is

Q: iving along a highway at 80 km/h, a 15-m long truck driving at 60 km/h is exactly 10 m ahead of you.…

A: Given data as per questionSpeed of car=80 km/hSpeed of truck=60 km/hLength of truck =15 mDistance…

Q: A rigid bar AB of length L = 1600 mm is hinged to a support at A and supported by two vertical wires…

A: Given that: LAB = length of bar AB = 1600 mm LAC = length of AC = 500 mm LAD = length of AD = 1200…

Q: If F = (350i - 250j - 450k) N and cable AB is 9m long, determine the x, y, z coordinate of point A.

A:

Q: A cylindrical pressure vessel of radius r = 10.2 in is filled with a gas at a pressure of 455.0 psi…

A: Given         Radius, r = 10.2 in Cap radius, R = 22 in    Pressure, P = 455 psi    Weight, W = 31…

Q: Where does the resultant of the two forces act? Replace the two forces with a single equivalent…

A: This is the given problem

Q: What are miller indices?

A: Introduction: An atomic plane's orientation in a crystal lattice is represented symbolically by a…

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

A: ● To solve this problem, first we need to determine the dimensions of BC and CD using trigonometric…

Q: A scale is constructed using the 10-kg mass, the 2.8-kg pan P, and the pulley and cord arrangement.…

A:

Q: The gusset plate is subjected to the forces of three members as shown in (Figure 1) The forces are…

A: GIVEN DATA- A SYSTEM OF FORCES IS GIVEN WE HAVE TO FIND TENSION T AND ANGLE θ

Q: ᴀ ᴋɴᴜᴄᴋʟᴇ ᴊᴏɪɴᴛ ɪꜱ ᴛᴏ ʙᴇ ᴀxɪᴀʟʟʏ ʟᴏᴀᴅᴇᴅ ᴡɪᴛʜ ᴀ ᴛᴇɴꜱɪʟᴇ ʟᴏᴀᴅ ꜰ. ᴛʜᴇ ᴀꜱꜱᴇᴍʙʟʏ ᴏꜰ ᴘᴀʀᴛꜱ ᴀɴᴅ ᴛʜᴇɪʀ…

A:

Q: * The resultant force has higher effect on the body than the group of forces when it replaces False…

A: ● The resultant force is the single equivalent force that can produce the same effect as that of the…

Q: the particle that is slowing down is stopped O accelerating O decclerating O

A: When an objec moves in a linear direction, then the displacement by the object in a unit time is…

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

A:

Q: What does it mean when the atomic packing factor is lower than expected?

A: The given question is  What does it mean when the atomic packing factor is lower than expected?

Q: The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam…

A:

Q: Describe the slip casting process in traditional ceramics processing. Also, what is the range of…

A: Given question: Describe the slip casting process in traditional ceramics processing.  What is the…

Q: Calculate the axial stress in a tube that is stretched by a tensile axial force of 4500 N if the…

A: Write the given data. F=4500 Ndo=25 mm=0.025 mdi=20 mm=0.020 m

Q: A- Define the following with mathematical expression if needed: 1- Closed system, 2- Cycle, 4-…

A: Thermodynamics is the branch of science which deals with energy and it's transformation.

Q: Suppose that F= 720 lb. (Eigure 1) Figure 1 of 1 Y Part A Determine the magnitude of the resultant…

A:

Q: What method of case hardening uses ammonia gas?

A: Nitriding is the case hardening process in which ammonia gas is used . As ammonia gas is used it…

Q: If F = 810 N , determine the tension developed in cables AB, AC, and AD

A: Given that: F = 810 N In the given configuration, it is required to determine the forces developed…

Q: ᴀ ᴘᴏᴡᴇʀ ꜱᴛᴀᴛɪᴏɴ ɪꜱ ᴛᴏ ꜱᴜᴘᴘʟʏ ꜰᴏᴜʀ ʀᴇɢɪᴏɴꜱ ᴏꜰ ʟᴏᴀᴅꜱ ᴡʜᴏꜱᴇ ᴘᴇᴀᴋ ᴠᴀʟᴜᴇꜱ ᴀʀᴇ 10,000 ᴋᴡ, 5000 ᴋᴡ, 8000…

A: Given:-  Individual peak value of loads are 10000 kW, 5000 kW, 8000 kW and 7000kW Diversity factor…

Q: Q3: Water (p= 990 kg/m³ & μ= 0.0013 Pa.s) is pumping from an atmospheric water tank to wa with…

A:

Q: QUESTION 3 Insulated container Nichrome heater Figure 2 Based on the manufacturer's details, a…

A: Given: The mass of heater, m = 3 kg The mass of water, M = 100 kg The initial temperature of the…

Q: Determine the reactions of the beam. 300 lb 100 lb/ft D1 8' D2 400 lb

A:

Q: B F Determine tension in bar AB and BC, if F=13013 N and theta-44 deg. Draw FBD diagrams in solution

A:

Q: The following are factors that affect fatigue life except: A Mean stress Surface treatments Case…

A: Fatigue life: The number of cyclic loading or cyclic stresses that any specimen can sustain before…

Q: A chain with length l is held stretched out on a frictionless horizontal table, with a length y0…

A: Solution: Given Data: *The length of the chain is: L *The length of the chain hanging down through…

Q: Research on the history of computer aided drafting and design. Include its earliest development up…

A: intro- research on CAD and design.

Q: What is the specific gravity of a gas having a density of 5.88 kg/m3? Correct Answer: 4.80 ± 0.1

A:

Q: QUESTION 1 a) Explain what is the basic difference between expendable and permanent molds used in…

A: Given question is

Q: (a) Determine the reactions at A and E if P = 1060 N. The reactions are positive if to the right or…

A: Given Data- A plane truss is given we have to find reaction forces and Pmax

Q: How does bond energy work? What does its higher value indicate?

A: Bond energy is the quantity of heat needed to transform one mole of a molecule to its constituent…

Q: A solar-power-tower plant is considered for Houston, Texas. Heliostats with a total area of 400,000…

A:

Q: The uniform 18-m pole has a mass of 110 kg and is supported by its smooth ends against the vertical…

A:

Q: Q1) A homogeneous of M kg bar AB is supported at either end by a cable as shown in figure beside. If…

A: Draw the free-body diagram of the bar AB.

Q: Saturated liquid ammonia is entering a 50 cm diameter 10-m long pipe at a steady 0.1 kg/s mass flow…

A:

Q: Problem 1.3 - Modes of Heat Transfe Using heat transfer relations, a) For the steel beam in Figure…

A: a)  Given           Temperature, T1 = 298 K                                  T2 = 273 K Thermal…

Q: Consider water that is at 7MPa pressure and has an enthalpy of h-3261.7 (kJ/kg). What is entropy per…

A: Given:Pressure of water, P=7 MPaEnthalpy of water, h=3261.7 kJ/kg

Q: words, describe the difference between the magnitude of a vector and the direction. In addition,…

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.