Determine the values of the stress in the steel bar as shown in the figure below when the temperature of the bar is-50°F, knowing that a close fit exists at both of the rigid supports when the temperature is +75°F. Use the values E = 29 x10 psi and a=6.5 x106 /°F for steel. A = 0.6 in B - 24 in.- A 67,860 lbs B 14,137.5 lbs C) 28, 275 bs D) 2827.5 Ibs

Determine the values of the stress in the steel bar as shown in the figure below when the temperature of the bar is-50°F, knowing that a close fit exists at both of the rigid supports when the temperature is +75°F. Use the values E = 29 x10 psi and a=6.5 x106 /°F for steel. A = 0.6 in B - 24 in.- A 67,860 lbs B 14,137.5 lbs C) 28, 275 bs D) 2827.5 Ibs

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.19P: At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with...

See similar textbooks

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
A piston-cylinder has a force F₁ applied to it. The circumferential stress in the cylinder cannot exceed Omax = 6 MPa. Hint: 1. Pressure = F Area P = F₁ F₁- OG Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value T'inner 44 mm t 1.25 mm r1 a. Determine the max pressure that the piston-cylinder can withstand, P. b. Determine the magnitude of max force that can be exerted on the piston to not exceed omax, F1. kPa N
A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The 0.27] that has a yield strength vessel will be constructed from a special steel [E = 224 GPa; v = of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I
Two vertical steel rods support the rigid bar as shown. Initially, the rods are stress-free. Given the data below, determine the stress of rods A and B after the 20 kN load is applied. Neglect the weight of the bar and use E = 200 GPa for steel. L= 3 m D = 3.5 mm A. Stress of rod A (MPa) B B. Stress of rod B (MPa) C. At what temperature AT change would the stresses for both rods be equal? Use a = 11.7 L= 4 m x 10-6 mm/mmC° (C°) D = 5 mm 4m 2m 2m 20 kN