determine force member GF, FB, BCConsider the Fink truss shown in (Figure 1). Suppose thatF₁ = 400 lb and F2 = 800 lb.Figure<1 of 1>F60° 60%-10 ft-A30°-10 ft-F₂BF₂E30°-10 ft-D

Answered: Image /qna-images/answer/4db9851b-e129-4df5-8161-f4f755db9b93.jpg

determine force member GF, FB, BC Consider the Fink truss shown in (Figure 1). Suppose that F₁ = 400 lb and F₂ = 800 lb. Figure < 1 of 1 > F A 30° -10 ft- F₂ B 000 B00 60° 60% -10 ft- E 30° 10- D

determine force member GF, FB, BC Consider the Fink truss shown in (Figure 1). Suppose that F₁ = 400 lb and F₂ = 800 lb. Figure < 1 of 1 > F A 30° -10 ft- F₂ B 000 B00 60° 60% -10 ft- E 30° 10- D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: x=71 The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree…

A: Cavitation: The process of formation of a vapor phase of a liquid when the liquid is subjected to…

Q: Identify the Occupancy Category of the structure using the NSCP 2015 provisions, and explain your…

A: Solution : The building to be categorised is a 9 story university building in Baguio City . Here ,…

Q: Find the reaction forces and all the force members with corresponding types of forces for the given…

Q: What is the minimum diameter of stirrups if the main bar reinforcement is 35mm?

A: Stirupps are mainly used to hold the primary reinforcement they prevent buckling and resist lateral…

Q: Within a month after the restoration of the asphalt pavement, on average, there is one…

Q: The data gathered from an experiment to determine the specific gravity of aggregates were summarized…

A: Given data: Weight of FA sample w1= 171.06 gm weight of SSD sample w2= 175.38 gm weight of…

Q: 2) The simply supported beam with a channel cross-section carries the loads as shown. Determine the…

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

A: Shear strain is measured as a change in angle between lines that were originally perpendicular.

Q: Q- Express the force F in Cartesian vector from if Point B is located 2m along the rode 6 m 6m D 0 F…

Q: 8 The following data are obtained from the current meter gauging of a stream, at a gauging sta-…

Q: What is the total settlement of the clay layer five years after the completion of primary…

A: This question is from Geo technical engineering

Q: A 5-g bullet is fired towards the right from a rifle having a mass of 4 kg. If the muzzle velocity…

A: Determination of velocity of recoil of rifle####

Q: Determine the height to be raised of box mars 12.4kg to gain Potential energy ergy of 133 2 J

Q: 3. A 13x127mm Plate of A36 steel is used as tension member. It's is connected to gusset plate with…

Q: Two wood boards, each 17 mm thick, are joined by the glued finger joint shown. The finger joint will…

Q: I have worked out reaction forces Ra and Rb, -= 3060N and 1710N respectively. could you please help…

Q: The shear strength Vc of a normal weight beam cross section, given concrete strength fc, width of…

Q: 2) The simply supported beam with a channel cross-section carries the loads as shown. Determine the…

Q: Question 1: Figure 1 shows the beams layout in one-way solid slab system in a reinforced concrete…

Q: (Triangulation): Two stations B and C were observed from a theodolite set up at station A and…

Q: With clear concise answer. Round off to 4 decimals thank u. Please answer in table same with the…

A: Let O be the origin as shown in image drawn.

Q: 3. A concrete is prepared by weight batching in the ratio 1: F: C with a water cement ratio of R. If…

A: Weight of Dry concrete = W kg Ratio of materials = 1:F:C Sum of ratios = 1+F+C Mass of cement…

Q: Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE…

Q: Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load…

A: To Determine Force in member AC, CD , DE

Q: 2) The simply supported beam with a channel cross-section carries the loads as shown. Determine the…

Q: to 2 significant figures. Use Francis Formula. A sharp-created weir 3.0 ft high extends across a…

Q: The theoretical discharge "Qt" can be computed by multiplying the actual value by the coefficient of…

A: Incorrect

Q: The beam shown in the figure is a two-span beam with a pin (hinge) in the center of the left span,…

A: We need to find the maximum Moment on the beam and compare it with the W 12 x 79 beam Moment…

Q: A new Civil Engineer failing to complete his first building contract worth P70,000 in a specified…

Q: Q1: A sag vertical curve connects a (-3.5%) grade and a (+0.5%) grade. The PVC is at station…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: d) e) f), with full solution

A: d) The yield point is the point on a stress-strain curve that indicates the limit of elastic…

Q: 10 ft 10 ft 25 k- A 2 k/ft 15 ft Hinge B 3 k/ft

Q: OWN solution/ action on how to resolve traffic congestion. Explain with specific details, and add…

A: Traffic is one of the main time-consuming parts in our daily life. This happens because…

Q: unique relationship between rainfall and catchment streamflow. Explain this statement spelling out…

A: A catchment is an area from which surface runoff is transported away by a single drainage system.

Q: Determine the maximum safe load P that can be supported by the bolted connection as shown if the…

A: The values and figure given in the question are as follows: Maximum allowable shear stress in any…

Q: Q1: Find the boundary layer thickness (6) equation, the shear stress (t) and the coefficient of drag…

A: Given velocity profile: uU=2yδ-3yδ2+3yδ5 Using von Karman momentum integral equation τoρU2=dθdc:…

Q: Distance between two stations A and B is 200 m whereas their difference in elevations is 2 m. Hence…

A: given- Distance between two stations A and B L=200 mDifference in elevations h=2 m

Q: Problem 3: Six 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the average…

Q: A 2500 mm gravity flow concrete aqueduct's length is 4 km with a head loss of 5.6 m. Assume pipe is…

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

Q: The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade)…

A: Velocity=76 mmsecP=80kPa=80×103 Nm2Condition ofr cavitationPabs<PV.P.Pabs=absolute…

Q: Problem 6: A rigid bar, hinged at one end, is supported by two identical springs as shown. Each…

A: Solution:

Q: Determine void ratio Porosity-0.142

A: Given data in question Porosity To find out Void ratio

Q: You have a pipe with an inside diameter of 3.48 in. and roughness 0.00032 in. A fluid with specific…

Q: Two wooden members, each having a width of b = 6.6 in. and a depth of d = 2.2 in., are joined by a…

Q: A bridge is proposed across a stream which has a catchment area of 3200 km². Ryve's coefficient of C…

A: Given data : The value of Ryve's coefficient C=10 The value of catchment area A=3200 km2 To find :…

Q: Fill in the blanks d: - 1 attachment Initial velocity of the ball, vo 29.50 m/s, upward from the…

Q: The backfill and foundation sand have unit weight of y = 135 pcf and Ø=38. The backfill has a slope…

Q: 18 брещi пашу д Slund is 1234. Determine demnity

A: Given data : The value density of water ρW=1000 kg/m3 The value of specific gravity S.G=1.234…

Q: (Triangulation): Two stations B and C were observed from a theodolite set up at station A and…

Concept explainers

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.

Question

determine force member GF, FB, BC
Consider the Fink truss shown in (Figure 1). Suppose that
F₁ = 400 lb and F2 = 800 lb.
Figure
<
1 of 1
>
F
60° 60%
-10 ft-
A
30°
-10 ft-
F₂
B
F₂
E
30°
-10 ft-
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q₁: Analyze the truss shown below B с <50k 3m IMI A E 100ku EA is Constant for all members + Am X Am
Two members AB and AC are made of material with E= 91 Gpa and each member has cross sectional area of A= 290 mm2. The members are used to support bar BC. If P-2079 N, L1= 202 mm , L2= 313 mm and L3= 480 mm. Answer the following questions. L3 E В to L1 L2 The tension in member AB%3D he tension in member The elongation in member AB=
Determine the forces in DF, EF, and EG in the truss shown diagrammatically in the figure. 40 kN 40 kN 40 kN DI B 2m E G K 6 @ 3m = 18m-
If the force in member AG of the truss in the figure below is 6 kN (C), then the :force (in kN) in member BG is d1=6.1 6 kN 3 kN 3 kN 1.5di 1.5di F di В di D -0.75d1 1.5di 0.75di
Question 26 The truss shown below has a hinge support at point A, a horizontal roller at point B, and is subjected to two poin loads (P1 and P2). If P1 = 20 kN and P2 = 123 kN, what is the force, in kN, in member DE? NOTE: Enter a positive value if the member is in Tension and a negative value if the member is in Compression. A 60° B 4 m E 4 m. 4 m 60⁰ D P1 (kN) 2 P2 (KN)
2. Determine the forces in member BC, BE and EF of the truss shown in the figure by Method of sections. a 50 kN atd RA 1 20 kN 3 panels @ 1.5 m 4.50 m- CBE=33.7 DEGREES RDY RDN Ro
F ANALYSIS OF STRUCTURE The truss shown in the figure is loaded with forces at the joints of the truss. Compute the internal forces in the members DF, FG, FH and GH only. Indicate if the internal force is a Tension B = 200 KN 9 m 50 KN В A or a Compression. You can use Method of Joint or Method of Section. 4 m C 4 mE 4 m G 3 m 3 m 20 KN 20 KN 20 KN 20 KN
F ., É, are applied to the truss system. В a) Find member forces in each member and state if the members are in tension or 4 m compression. b) If the maximum force that any member can support is Tmax in tension and Cmax in compression, determine the maximum value of P that can be supported. A E 3 т 3 m 3 т 3 m F1 F2 F3 F4 F5 Tmax Cmax P 2P 40° 7 kN 8 kN 2P Note: Do not show zero forces in your calculations.
The Pratt bridge truss supports five forces F=310 kN. The dimension L=8m Figure L B 1 D siis H M Search H 1 of 1
F ANALYSIS OF STRUCTURE D H = 150 KN 50 KN H The truss shown in the 9 m figure is loaded with forces at the joints of the truss. Compute the internal forces in the members DF, FG, FH and GH only. Indicate if the internal force is a Tension or a Compression. You can use Method of Joint or Method of Section. B A 4 m C 4 m E 4 m G 3 m I 3 m 20 KN 20 KN 20 KN 20 KN
Find the force in member Gl of the truss shown below. A 15kN 2m С D + B 15kN 2m F G E 15kN 2m H I 4m Solution : FGI=22.5kN(C)
Determine the force in member FG (assume FG is tension) of the truss shown in the figure below?. Set P = 671 lb. 2P 12h 12 12 12 Answer: