Design a voltage regulator that will maintain an output voltage of 20V across a 1 k load with an input that will vary between 30 and 50 V. That is, determine the proper value of R and the maximum current Izm. A bridge full-wave rectifier with forward resistance of 2 ohm supplies power to a 100 ohm load

Design a voltage regulator that will maintain an output voltage of 20V across a 1 k load with an input that will vary between 30 and 50 V. That is, determine the proper value of R and the maximum current Izm. A bridge full-wave rectifier with forward resistance of 2 ohm supplies power to a 100 ohm load

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Draw circuit diagram of a full-wave controlled rectifier and draw the wave shapes of output voltage and current for R-L load with sinusoidal input. You have to design a full-wave AC to DC converter circuit to have output average voltage of 40 and 50 W power to a 100 Ω resistive load from a source of 60 V. Is the design feasible? Why?
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
a full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35V to a 3.3k ohms load. Determine the minimum value of filter capacitor if the maximum peak-to-peak ripple voltage is to be 0.5V.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: a) Peak AC voltage Vm of the source b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?