Design a sequential circuit that detects prime numbers in the string of inputs using JK flip-flop. If the input is 1, the state tran.sition is 000, 011, 100, 111, 101, 010, 001, 110, then back again. Otherwise, the state transitions are the following: 000, 010, 101, 011, 111, 001, 110, 100, then back again. Include state stable, state diagram, flip-flop input and output equation, and logical diagram

Design a sequential circuit that detects prime numbers in the string of inputs using JK flip-flop. If the input is 1, the state tran.sition is 000, 011, 100, 111, 101, 010, 001, 110, then back again. Otherwise, the state transitions are the following: 000, 010, 101, 011, 111, 001, 110, 100, then back again. Include state stable, state diagram, flip-flop input and output equation, and logical diagram

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

You want to design a synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and will not count the decimal digits in the last two digits of your student number. a. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. b. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last two numbers 02
5. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J,K inputs are connected with a constant "high"(logic 1). All the JK flip-flops in Figure 2 are negative edge triggered. All the initial values of Q2Q1Q0 are 0. Qo (LSB) (MSB) Input K K Logic 1 Input Q2 000 Figure 2. Counter (a) Sketch the output waveforms forQ2 Q1 Q0. Write down the output binary value (Q2Q1Q0: such as "000", "001") for each clock period on the figure. (b) Describe the function of the counter (e.g. binary down counter counting from 7 to 0).
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
show the waveforms for each flip-flop output with respect For the ring counter in Figure to the clock. Assume that FF0 is initially SET and that the rest are RESET. Show at least ten clock pulses. D D. FFO FF1 FF2 FF3 FF4 FF5 FF6 FF7 FF8 FP9 CLK
Question: The flip-flops in the drawing below are positive edge triggered D flip-flops. Let Q2, Q1, QO = 0,0,0 initially. a) Plot the clock, Q2, Q1 and QO until the outputs begin to repeat. b) Show the circuits acts as a counter 00 1000 Hz/50%
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the circuit goes through the state transitions from 00 to 10, to 01, to 11, back to 00, and repeats. When x_in = 1, the circuit will reverse the given sequence. a. Using D Flip-Flop. b. Using JK Flip-flop. Provide the state diagram, state table, state equations, and the circuit diagram.
4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Design a 2-bit counter using D-Flip flops with one input. When the input is 0, the ww m wwww w w m w i ww ww wwww www counter counts down, with the repeated sequence (11-10-01-00). When the input is 1, the counter counts repeated random sequence (00-01-11-10). a) Derive the state table for the sequential circuit. wwwww b) Derive the simplified flip flops input equations. www w w ww www m www ww c)Draw the logic circuit diagram of a 2-bit counter.
Design a Up Down Counter by using JK flip flop and verify the output of your designed circuit onany random input. Provide the following information as well:1. State table2. State diagram3. State equations4. Complete circuit diagram
5. A sequential circuit has two flip-flops A and B, one input X, and one output Y. The state diagram is shown in the following figure. Design the circuit with D flip-flops using a 1-hot state assignment. 00/1 01/0 11/0 10/0
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the state of the circuit remains the same. When x_in = 1, the circuit goes through the state transitions from 00 to 01, to 11, to 10, back to 00, and repeats. a. Using D Flip-Flop. b. Using JK Flip-flop.