Design a round spiral column to support an axial dead load of 500 KN and an axial live load of 650 KN. Assume that 3% longitudinal steel is desired, f'c = 35 MPa and fy = 420 MPa. Use 16 mm diameter main reinforcement. determine the spacing of 10 mm spiral (fy = 275 MPa) with 30 mm steel covering. use NSCP 2015 standard

Design a round spiral column to support an axial dead load of 500 KN and an axial live load of 650 KN. Assume that 3% longitudinal steel is desired, f'c = 35 MPa and fy = 420 MPa. Use 16 mm diameter main reinforcement. determine the spacing of 10 mm spiral (fy = 275 MPa) with 30 mm steel covering. use NSCP 2015 standard

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.8.9P: Use the composite beam tables and select a W-shape and stud anchors for the following conditions: ...

See similar textbooks

Similar questions

Assume Grade 50 steel and use f. = 5,000 psi for parts (a) thru (b). (a) u The beam below is subjected to a factored moment M₁ = 800 ft-k. Assuming that the reinforcement is to be placed in two layers as shown, design the reinforcement. (b) Calculate the moment strength oM₁ of your design in part (b) and compare that with the factored moment M₁ = 800 ft-k. Is your design adequate? Be sure to check the strain in the tension steel. A k 6" 4" 6" ....... 4" 12" 8" 4" 4"! 32"
USE NSCP 2010 A simply supported beam is reinforced with 4 – 28 mm ø at the bottomand 2 – 28 mm ø at the top of the beam. Steel covering to centroid ofreinforcement is 70 mm at the top and bottom of the beam. The beamhas a total depth of 400 mm and a widthof 300 mm. fc’ = 30 MPa, fy = 415 MPa. Balanced steel ratio ρb = 0.031.Compute the ultimate moment capacity of the beam in kN-m. Usereduction factor of 0.90
a) For the rectangular section shown below the maximum allowable tensile stress in the concrete Fct = 3MPa. Assume an uncracked section and find the maximum moment the section can resist as well as the stress in the reinforcement for this moment Ec:= 30-GPa Es:= 200 GPa b:= 300 mm h := 520 mm d:= 460 mm 2 As 1470 mm := b As
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with d-20-mm-dismeter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is M0 mm and at the bottom is 70 mm. Use concrete strength r'e-21 MPa und steel yield strength fy 415 MPa for 20- mm bars and fy= 275 MPA for 16 mm bars Detenmine the design moment capacity n kN m of the beam in negative bending. A 40.06 O45.07 C. 42.70 D47.55
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
An existing T-beam section was investigated and found out the following elements: Top bar reinforcement: 1500 mm2 Bot bar reinforcement: 2500 mm2 thickness of slab = 100mm effective depth from the surface of the slab = 450mm effective width of flange = 1000mm Top bar concrete cover at center of the bar = 50mm fy = 414Mpa f'c = 28Mpa use f’y = fy Determine the depth of compression block in mm, in 3 decimal places.
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __ mm
A composite compression member consists of a W12 x 136 encased in a 20-in. x 22-in. concrete column as shown in Figure Four #10 bars are used for longitudinal reinforcement, and #3 ties spaced 13 inches center-to-center provide the lateral reinforcement. Assume a concrete cover of 2.5 inches to the center of the longitudinal reinforcement. The steel yield stress is Fy = 50 ksi, and Grade 60 reinforcing bars are used. The concrete strength is f,c =5 ksi. Compute the available strength for an effective length of 16 feet with respect to both axes.