Design a combinational circuit with four inputs and one output. The output is 1, when the binary value of the input is less than or equal to 3, the output is zero otherwise. The output is 1 when the binary value of the input is a prime number greater than 9. a) Obtain the truth table. b) Find the simplified output function in sum of products. c) Draw the logic diagram using NOR gates only.

Design a combinational circuit with four inputs and one output. The output is 1, when the binary value of the input is less than or equal to 3, the output is zero otherwise. The output is 1 when the binary value of the input is a prime number greater than 9. a) Obtain the truth table. b) Find the simplified output function in sum of products. c) Draw the logic diagram using NOR gates only.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
Use Digital Logic Simulator Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adder
Draw the equivalent logic diagram of the set-up below
In a home security system, the main door (O) of home is controlled by a logic operation with the help of RFID card. the Owner, Mrs. Owner, Security Guard and Guest have a designated RFID card - Owner with card W, Mrs. Owner with card X, security guard with card Y and guest with card Z. Whenever, any of the card is NOT inserted, Door remains Closed; when, all the cards are inserted together, the Door is opened. Consider, card NOT inserted as Logic Low (0), card inserted as High Logic (1), door open as Low Logic (0) and door close means High Logic (1).(i) Identify the logic based on the problem statement(ii) Develop the truth table (W, X, Y & Z – inputs, O – output)(iii) Find the Standard SOP and Standard POS expression(iv) Find the Simplified SOP expression using KMAP.(v) Design the system using basic logic gate.
1. Design a 16 - to - 1 multiplexer using 4- to-1 multiplexer. 2. Using K- Map, simplify the following Boolean expression : Y = Σ (1,3,5,7,9,10,11,13,14,) 3. Build the logic circuit for the following function using Programmable Logic Array (PLA). ?? = ??? + ??? + ??? + ??? ?? = ??? + ??? + ??? + ???
Draw a truth table, Karnaugh diagram and logical gates circuit to show the functionof an even number detection circuit. That is, the output of the circuit will be one only ifthe value of the binary input is even. Assume three inputs.
Fill in the truth table below. Draw the Karnaugh map and show it in its simplest form. Draw the logic circuit. running state = 0 fault state = 1 please fast
Draw a block diagram, truth table and logic circuit of 1*16 Demultiplexer and explain its working principle.
Design a circuit with logic gates that tell us if a number less than 10, codedin binary, it is either prime (1) or not (0). Minimum up to 16 combinations.True tableII. Boolean functionIII. Simplification procedure by any of the methods
Consider two binary numbers where the first is made of three bits whichcan be represented by X, Y, and Z, while the second is two bits and isrepresented by A and B. Design a logic circuit that multiplies X Y Z timesA B, using two half adders, one full adder in addition to AND gates.
Draw the logic diagram using basic gates for the expression Y=(A’+B)(B'+C) with truth table and implement using NOR gates
Draw the logic circuit for the given expression clearly.