Describe the region of operation of the BJT when it is used as a switching circuit and sketch the output voltage waveform of the circuit For the BJT switch cireuit as shown in the figure given below. 12V Rc- 212 Re 33V oW a What minimum value of Is is required to saturate this transistor if Boc is 1507 Ne Vez (sat). Des cribe the significant of this current. b. Calculate the maximum value of R, when Va = 3.3 V.

Describe the region of operation of the BJT when it is used as a switching circuit and sketch the output voltage waveform of the circuit For the BJT switch cireuit as shown in the figure given below. 12V Rc- 212 Re 33V oW a What minimum value of Is is required to saturate this transistor if Boc is 1507 Ne Vez (sat). Des cribe the significant of this current. b. Calculate the maximum value of R, when Va = 3.3 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. a) Define and describe the Q-point, DC load-line, and AC load-line. b) Is a JFET a voltage controlled or current controlled device? c) What are the roles of the resistor Rs and Rp in a JFET bias circuit?
What happens to the transistor when at cut-off operation? a. maximum current flows from emitter to collector b. the transistor is at its operating point c. there is no base current d. no current flows from emitter to collector
The term cut-off for a transistor refers to a. the transistor is at its operating point b. no current flow from emitter to collector c. maximum current flow from emitter to collector d. there is no base current
What is a BJT transistor and how does it work in amplification and switching circuits?
The mode of operation for the D-MOSFET is Select one: a. the ohmic region only b. the enhancement mode only c. both the depletion and enhancement modes d. the depletion mode only
FETs have similar properties to ___. a. Scotty diodes b. NPN transistors c. PNP transistors d. uni-junction transistors
For the circuit shown in Figure B23, a- 0.97, calculate the following: i. Collector current (Ic) ii. Collector-Base voltage (Ven) i. Emitter Current (I) iv. Base Current (In) Ic 2.5 kl Ouput 2.8V IB 10V Vec
3. Briefly explain the function of each terminal for Bipolar Junction Transistor. 4. Named the three BJT modes of operations? Explain each mode of operation. 5. Explain the Basic operation of a BJT. How is a BJT become an amplifier or a switch?
For the circuit shown in Figure B23, a = 0.97, %3D calculate the following: i. Collector current (Ic) ii. Collector-Base voltage (VCB) iii. Emitter Current (IE) iv. Base Current (IB) IE Ic 2.5 k Ouiput 2.8V IB 10V VEE Vcc Figure B23
List the basic relationships for a transistor:
A power BJT is used as a power -7 control switch by biasing it in the cut off region (off state) or in the saturation region (on state). In the on state a) both the base-emitter & base- collector junctions are forward biased b) the base-emitter junction is reverse biased, and the base collector junction O is forward biased c) the base-emitter junction is forward biased, and the base collector junction O is reversed biased d) both the base-collector & the base- emitter junctions are reversed biased In a BJT, the outer layers are much -8 more thick as compared to the middle .layer a) True b) False O
Electronics Circuit: BJT biasing .A Voltage Divider bias NPN BJT (Beta = 80) circuit is connected to a 16VDC supply with the following components R1= 62 KOhms, R2= 9.1 KOhms, Rc= 3.9 KOhms, and Re= 0.68 KOhms. Determine the Emitter Voltage (Ve). a. 1.16 Volts b. 1.86 Volts c. 9.33 Volts d. 8.17 Volts