D. Design a sequential circuit with eight (8) states and the state transitions are defined in the table shown below. (a) Derive the state table with JK flip-flop inputs using the JK flip-flop excitation table. (b) Derive the JK flip-flop input equations. Present State a b C d h Next State x = 0 8 d f 8 x = 1 b C e a C b h a Output x = 0 0 0 0 1 0 1 x = 1 0 0 0 0 0 1 0

D. Design a sequential circuit with eight (8) states and the state transitions are defined in the table shown below. (a) Derive the state table with JK flip-flop inputs using the JK flip-flop excitation table. (b) Derive the JK flip-flop input equations. Present State a b C d h Next State x = 0 8 d f 8 x = 1 b C e a C b h a Output x = 0 0 0 0 1 0 1 x = 1 0 0 0 0 0 1 0

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially Low. HIGH CLK- CLR nnnnnnn CLK PR CLR
A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are attached below: a) Draw the logic diagram of the circuit. b) Derive the state equations for A and B c) Tabulate the state table. d) Draw the state diagram for the circuit and describe the function of circuit.
Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially LOW. PR HIGH CLK- K CLR CLK- PR CLR
1) by creating the state table for the state diagram given below a) draw logic diagrams by designing Sequential Circuits with JK Flip flops. b)Draw logic diagrams by designing Sequential Circuits with D-Type Flip flops.
Design and implement sequential digital circuit, with following specifications: It has one input X, two outputs Y1 and Y0.Whenever an active HIGH is observed at input X at the active clock edge, circuit initiates a sequence and generates output waveforms given in figure below. (After the sequence is completed, it waits for input to be HIGH again) a)Use AND, OR, NOT gates and D type edge triggered flip-flops.Hint: Describe the circuit model Draw the State Diagram Find the State Table Make State Assignment with increasing numbers. (i.e. 0,1,2,3...) Write State and Output equations Draw the Circuit.
Two edge-triggered J-K flip-flops are shown in figure below. If the inputs are as shown, draw the Q output of each flip-flop relative to the clock, and explain the difference between the two. The flip-flops are initially RESET. CLK CLK -C CLK- K K (b)
Determine the output Q for the given J-K flip flop and the waveforms. HIGH PRE J. CLR PRE %3D 3D
Explain and design a mcd-6 co:unter using J-K flip flop. [
The following statements describe the sequential circuits. Select all the TRUE statements. a The sequential circuits consist of a combinational circuit and storage elements. b The storage elements keep a binary bit even though the circuit power is gone. c Only the current input determines the outputs of sequential logic circuits. d The flip-flop is controlled by signal levels.
Q#01: The schematic shown in figure below is for Divide_by_11, a frequency divider, that divides clk by 11 and asserts its output for one cycle. The unit consists of a chain toggle-type flip-flops with additional logic to form an output pulse every 11th pulse of clk. The asynchronous signal rst is active-low and drives Q to 1. Develop and verify a model of Divide_by_11. Vcc 20LSB Q2 03MSB clk clk clk clk clk rst rst rst rst wl w2 clk QB cik_by_11 rst rst