gineering(d) What is the time constant r of theresponse? Plot the response v,(1)and give the values of v, at t = r,2T, and 5 r.R 10 k2-wwtC= 1pFR=10 k2ww= 10 VFigure P10.22 Op-Amp circuit for problem P10-22. 10-22. A constant voltage source vn(t) = 10volts is applied to the Op-Amp circuitshown in Fig. P10.22. The output volt-age v,(t) satisfies the following first-order differential equation and initialconditions:dv.(t)+V。(1) = -V(り、0.01dtinv.(0) = 0 V.%3D(a) FindVotran (1).(b) Find the steady-state solution vif vin = 10 V.(c) If the initial output voltage isv.(0) = 0 V, determine the totalthetransient solution,Figure0.55%3Dresponse.

Answered: (d) What is the time constant r of the…

(d) What is the time constant r of the response? Plot the response v,(1) and give the values of v. at t = t, 2r, and 5r. R = 10 kly ww- C= 1uF R = 10 k2 ww Vcc Vin = 10 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

9 Derive the output voltage expression for the circuit given below. Vi R Vo VI Based on the Output Input Relationship what is the name of the circuit Trace the output graphs for the given TWO inputs (Sinusoidal and Square)
For the circuit shown in figure, derive the expression for stability factor S(B). Q+Vcc Rc RB ww
Solve for Vp and Vs. Show your complete solution. (When you try to simulate the circuit in LTSpice where (Vin=0 DC Offset, 10V amplitude, 1MHz frequency), Vp=8V and Vs=40V. I want to learn how to get these values by solving) Will upvote is complete solution and correct. Thank you.
a) Describe with the aid of suitable diagrams, the three types of stable output response to a step input produced by a second order system. b) The step response of a second order system is shown in Figure Q6. Magnitude 3 Result of Instruments Step Response 2.75 mmmm mm mm mm I 1.5 3 c) 2 1 ww www www m 1900 1999 1998 199988 0.5 1 Percentage overshoot Time to the first peak Damping factor, < Undamped natural frequency, wn 0 0 Find the: i) ii) Find the: i) ii) 2 Time (seconds) Figure Q6 2.5 3.5 4
For the electric circuit given in the figure;a) Obtain the transfer function between V2(s) and V1(s).b) Calculate the gain value and time constant of the system in steady state as C=2MicroFarad, R1=R2=1Mohm.c) According to the values given in option B, obtain the expression to be obtained at the output for the unit step input by using the residual sum method.
Problem 3: Design a buck-boost converter to meet the following specifications. Assume that the ESR of the 40x106 capacitor in the available type is given by ESR = 2, where C is the capacitance in C Farads (this information is given so that the students do not have to refer to a capacitor datasheet to complete this design; for example, if you need to limit the ESR to be less than 0.12, based on the design equations given in the notes, then C should be more than 400 uF for this type of capacitors). Vin = 10V - 14Vdc; Vo = 12Vdc; I, max = 5A; Io_min = 1A fs = 100kHz; AV, < 100mV (pk – pk)
Please write every step of your solution For the circuit given below find the operating point of the nonlinear resistor and then make small signal analysis (consider both roots) to find the approximate voltage VR(t) and current ir(t) of the nonlinear resistor. Vo = 9V, R1 = 32, VR = iR? - Sir – 15, e(t) = 0,1 sin(5t) İR R1 e(t) VR Vo
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
In the electrical network given in the Figure, the output voltage is taken over the coil. R = 1k ohm, C = 1μF and L = 1 mH. a)Since the switch is closed at time t = 0, the input and the relationship between output voltages. Determine the differential equation shows. b)Find the transfer function. c)Unit impulse and unit step function type input voltages versus output voltages calculate and change changes according to time. Draw it to scale.
522 iii. G(s) = $³+24s²+166s+1044 a) Find the location of the poles, natural frequency and damping ratio values....... b) Determine the forms and write the general expression for the unit step response. c) Find Css (steady state value) and Peak value:............. d) Revise each transfer function to produce unit step response double approximately two tim slower....... **********
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : ii. Determine the inductor's turn ratio.
In the circuit shown below the op-amp slew rate is SR=05 V/us. If the amplitude of input signal is 0.02 V, then the maximum frequency that may be %3D used is 240 k2 10 k