d- The ripple frequency in the output voltage of single-phase half-controlled bridge AC/DC converter is when a > 60°. 1- 3f, 2-6f, 3- 2f, 4- f, 5- None of previous. ************** e- The integrator in the firing circuit of 1-phase bridge AC/DC converter is necessary to have firing angle range. 1-0-90°, 2-0-120°, 3-0-180°, 4-0-360°, 5- None of previous. f The harmonic contents in an inverter can be reduced through the use of modified Voltage, 2- Full, 3- Reduced, 4- Commutation, 5- None of previous. ****** PWM. 1-

d- The ripple frequency in the output voltage of single-phase half-controlled bridge AC/DC converter is when a > 60°. 1- 3f, 2-6f, 3- 2f, 4- f, 5- None of previous. ******** e- The integrator in the firing circuit of 1-phase bridge AC/DC converter is necessary to have firing angle range. 1-0-90°, 2-0-120°, 3-0-180°, 4-0-360°, 5- None of previous. f The harmonic contents in an inverter can be reduced through the use of modified Voltage, 2- Full, 3- Reduced, 4- Commutation, 5- None of previous. PWM. 1-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
1. Single phase half-wave converter has a purely resistive load of R and delay angle is a= n/2 determine: (a) Rectification efficiency (b) Form factor (c) Ripple factor.
Industrial Electronics If the given types of DC-DC Converter has an input voltage of 25V. The output voltage of each converter using a duty cycle of 0.4s. a.) Buck Converter Vout?b.) Boost Converter Vout?C.)Buck-boost converter Vout?
A 10-Ohm fully resistive load system will be fed from a photovoltaic (PV) module. Load (converter output) voltage 12 V DC is required. But the PV output is DC 18 Volt. Buck type DC/DC converter design is required between load and PV. For this j-converter, the inductor current must be continuous and the fluctuation rate of the load voltage must be at most 0.5%. The lowest switching frequency is 40 kHz; A) What is the lowest Capacitor value (microF) that meets the design conditions for the output capacitor ? B) What is the RMS value of the inductor current (A) ? C) What is the average value of the inductor current (A) ?D) What is the inductance value (microH) that meets the design prerequisites?E) What is the lowest inductance value to be calculated (microH) ?F) What is the operating ratio of the circuit (Duty) ?
A 10-Ohm fully resistive load system will be fed from a photovoltaic (PV) module. Load (converter output) voltage 12 V DC is required. But the PV output is DC 18 Volt. Buck type DC/DC converter design is required between load and PV. For this j-converter, the inductor current must be continuous and the fluctuation rate of the load voltage must be at most 0.5%. The lowest switching frequency is 40 kHz; A) What is the lowest Capacitor value (microF) that meets the design conditions for the output capacitor ? B) What is the RMS value of the inductor current (A) ? C) What is the average value of the inductor current (A) ?D) What is the inductance value (microH) that meets the design prerequisites?E) What is the lowest inductance value to be calculated (microH) ?F) What is the operating ratio of the circuit (Duty) ? Please answer D;e;f
Draw circuit for Boost Converter. Also derive its Output equation. What will be the value of Duty Cycle (D) if the input voltage is 50 V DC and desired output voltage is 20 V DC.
Three Phase Semi Converter When Highly Inductive Load Connected: Please derive the following equations, Thank You :-)
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
This part deals with DC-DC converters. A. Draw the circuit for boost dc-dc converter and explain its principle of operation. B. Derive the input-output relation for a boost dc-dc converter in the case of discontinuous current flow mode of operation. solve both part and fast
Please written by computer Answer the following questions:a. Name a suitable topology that can be used in the above DC/DC converters to achieve the required regulation with the minimum provided efficiency.b. Calculate the efficiency of the linear regulator.c. Calculate the total input power and the input current.d. Calculate the overall efficiency of the system.e. If a 100uF capacitor is used at the input to minimize the ripple. Assume the rise time of the input source is 0.2ms. Estimate the maximum inrush current to charge the capacitor to 12V.