Create a conclusion about basic GIS Application: Site Selection Analysis.
Q: A residential area located in an urban zone of Basrah governorate is served by the triangular pipes…
A:
Q: Calculate the support reactions of the following beams. Also draw the shear and moment diagrams
A: Given Data Find the support reaction and draw shear force and bending moment diagram.
Q: Q.1 (a) A sluice gate in a 2.0 m wide horizontal rectangular channel is discharging freely as shown…
A:
Q: The towers at the opposite side of the river supports the load W = 50 kN as shown in the figure. The…
A: Given: W = 50 KN, L = 20m, d = 1.5m Required: a. At what distance from A should the load be…
Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with angle of…
A:
Q: wwwww Q- Traffic volume count has been collected on a 2-lane road section which needs upgradation…
A: Given- 2 lane road sectionmax flow=1280 veh/h per lanePHF=0.78125AADT=12270 veh/day It is needed to…
Q: A WF16x67 is made from A572 grade 50 steel. A ¾ in. cover plate, 9in. wide, is welded to the top…
A: (a) No plate on top A WF16x67 beam without a cover plate may have its plastic moment strength…
Q: 7 4 The precast floor system consists of a 150-mm-thick concrete slab carry its self weight as well…
A:
Q: INUTO: Top C] Draw the shear force V and bending moment M diagrams for the frame showr 135 KN - 4 m…
A:
Q: Give examples of problems that may arise when a designer fails to give adequate attention to the…
A: 1. Delays in Construction: Poor design choices may lead to delays in building, which can be caused…
Q: Find level of service (LOS) for an old freeway in Basrah city with the following characteristics:…
A: Given:- The free flow speed (FFS) = 65 mi/hr The peak hour factor (PHF) = 0.80 The number of lanes…
Q: sosceles traingle gate AB is hinged at A and weights (155 kg). What horizontal force P is required…
A: Given : S.G =0.83 Now , L=2sin 50°=2.610the width of gate is not clear so assumed 1 mArea of Gate=12…
Q: The most suitable distribution for transmissivity is?
A: The most suitable distribution for transmissivity is the Log-normally distributed transmissivity.…
Q: The velocity of a particle is given by V=25t^2-80t-200, where V is in feet per second and t is in…
A: Give: V = 25t2 - 80t - 200
Q: The soil profile from a geological map of a project site obtained during a Phase I investigation is…
A: The steps to be followed: 1. Making plans for a soil exploration campaign. 2. Taking soil or rock…
Q: Question 2. The concrete column (30 x30) cm, length 6 m, Ec = 4 x 105 MN/m² and ac = 5.5 x 10%/ "C…
A:
Q: For the net cash flow series, find the external rate of return (EROR) using the MIRR method with an…
A:
Q: A 20-ft wrought iron bar that is ½ inch in diameter is subjected to a tensile force of 3 kips.…
A:
Q: Calculate: AMax using virtual work method.
A: The maximum deflection of beams occurs where slope is zero. Slope of the beam is defined as the…
Q: Question No. 22 The ordinates of a 2-h unit hydrograph at I hour intervals starting from time t = 0,…
A: Given- Total rainfall P=6.6 cm Duration of rainfall D=3 h ϕ-index=2 mm/h=0.2 cm/h Base flow B=5 m3/s…
Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with angle of…
A:
Q: Determine the actual runway length after applying necessary corrections for elevation and…
A:
Q: explain the causes and process of b) Seawater intrusion
A: Sea water intrusion:- The passage of salty water into freshwater aquifers is known as sea water…
Q: Compute the effective stack height of a coal burning power plant with physical stack height of 200 m…
A:
Q: A36 steel and 3/4 in bolts are used in the bolted splice shown in figure P4.48 . Consider yield,…
A: For A36 grade yeild stress Fy = 36 ksiUltimate stress = 58 ksisince all the members of connection…
Q: Question 5 Figure 5 shows a header tank in a laboratory. a) Determine the discharge when filling the…
A: Given, Pipe diameter AC = 22 mm Pipe diameter BC = 100 mm Pressure head at B = 35 m
Q: (a) A rectangular channel 2.0 m wide has a discharge of 250 lit/sec which is measured by a right…
A:
Q: Two methods can be used to produce solar panels for electric power generation. Method 1 will have an…
A: The company should select Method 1. Since the analysis is being done over a three-year planning…
Q: 12 13 14 15- Design slow sand filters for a population of 40000 with an average rate of water supply…
A: Given:- Pulation (P)= 40000 Discharge= 150 lit/c/day Design slow sand filter.
Q: A +0.7% grade meets a -0.4% grade at sta 2+700 and at elevation 30 m. The max allowable change in…
A: Given information, n1 = 0.7% n2 = -0. 4% Maximum allowable change in grade/sta.=0.2%
Q: Time: 0 m 0 s Q. The state of stress at a point in a body is given by ox = 50 MPa and oy = 100 MPa.…
A: Given data- A state of stress at a point is given- σx=50 MPa,σy=100 MPa, Principal stress- σ1=200…
Q: A 10 kN/m 8m B 2 m 20 kN
A:
Q: Problem 6: Inputs: ● ● ● ● a = 600 mm b = 400 mm c = 200 mm F = 100 N The line of action of the…
A: Given: a = 600mm b = 400mm c = 200mm F = 100N Required: Moment at point A considering different…
Q: By what means does activated charcoal decolorize dye in wastewater? How does activated charcoal…
A: Activated Charcoal decolorize dye is the most effective method of removing certain organic…
Q: A 5m high vertical earth retaining wall retains a dry granular backfill with angle of internal…
A:
Q: The following are given for a specimen of soil: M = 300 g, Msolid = 170 g, Gs = 2.72 and S = 70%.…
A:
Q: Assume the section has cracked and use the transformed-area method to compute the required…
A:
Q: PROBLEM 1: For the determinate beam shown below, construct the quantitative influence diagrams of…
A:
Q: A hollow steel member has an inside diameter of 50mm,a wall thickness of 5mm,a length of 1500mm and…
A: L=1500mm P=5kN E=210GPa To find change in thickness and elongation
Q: A 16 mm thick plate measuring 650 mm x 420 mm is used as a base plate for an ISHB 300 column…
A: Given: A 16 mm thick plate measuring 650 mm×420 mm used as base plate. Factored axial compressive…
Q: 3. For the given cross-section, determine the location of the centroid and the moments of inertia…
A: Answer Calculation of the location of the centroidal axis Location of Centroidal horizontal axis…
Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with angle of…
A:
Q: 30 Compute the safest minimum diameter of the cables if the allowable axial stress of t he cable is…
A: Given Data Allowable axial stress = 60 MPa Find the safe diameter of cable (d)
Q: 2. A block made of 40MPa concrete with dimensions as shown. What is the maximum force that it can…
A:
Q: A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm…
A: Given data- A double cover butt riveted joint- Two flat plates of 200 mm width, b=200 mm, Thickness…
Q: Torsion A square beam of size 400 mm x 400 mm is subjected to a factored bending moment and twisting…
A: The size of the square beam = 400 mm × 400 mm The magnitude of the factored bending moment = 200…
Q: 4. Phase Diagram A soil sample was obtained at the underground parking garage that Dr. Barry is…
A: Given Data Total volume of soil (VT) = 0.05 ft3 Total weight of soil (WT) = 4.2 lbs Weight of…
Q: Torsion A square beam of size 400 mm x 400 mm is subjected to a factored bending moment and twisting…
A:
Q: Determine the superimposed uniform load at the beam if the tensile stress at the bottom fiber is…
A:
Q: Please find normal discharge for a 400mm diamter drainage pipe. manning's n = 0.013 the pipe is…
A: Given Data Partially pipe flow Diameter of pipe (D) = 400 mm Manning constant (n) = 0.013 Angle =…
Create a conclusion about basic GIS Application: Site Selection Analysis.
Step by step
Solved in 3 steps
- Civil Engineering What is rubber sheeting or conflation as used in GIS? What problems must be considered when perform a rubber sheeting operation in a GIS? (this question is related to Geographic Information System course)Define GIS.Question 4 Subject:Geographic Information System Show how spatial data (Such as Raster Data) analytics are done for any GIS applications.
- Q- The plan of a map was photo copied to a reduced size such that a line originally 100mm, measures 90mm. The original scale of the plan was 1:1000. Find the revised scale.1.13 List the legal requirements for registration as a land surveyor in your state. 1.14 Briefly describe an Earth-Centered, Earth-Fixed coordinate system. 115 List the professional societies representing the geospatial industry in the a a b C. TRUCTION ILLUSTRATED United States Canada International SIXTH EDITION WILEY hpTraverse surveying.