Correct the following false statements: 1) One of the main advantages of resistance temperature detector (RTD) is the high sensitivity (a major change in resistance per degree).? 2)Because the thermistor covers high temperature range, it can be used for measuring the temperature in oven and furnace. ? 3) The LM34 (I.e., IC temperature sensor) produces an output voltage that is proportional to Kevin temperature.?

Correct the following false statements: 1) One of the main advantages of resistance temperature detector (RTD) is the high sensitivity (a major change in resistance per degree).? 2)Because the thermistor covers high temperature range, it can be used for measuring the temperature in oven and furnace. ? 3) The LM34 (I.e., IC temperature sensor) produces an output voltage that is proportional to Kevin temperature.?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

In half wave rectifier circuit (Vrms = Veff): 1) What is the average value (V0) of the output voltage? 2) Draw the waveform of the output signal over one period.
FULL WAVE RECTIFIER CIRCUIT: Explain what happens to the “output” LED (i.e. the LED marked “vo”) as the frequency is increased from low frequency (1 Hz) to higher frequencies (closer to the main supply frequency of 50 Hz)
4. Draw and explain the circuit of a simple AM demodulator using Junction diode ( draw the input and output waveforms )
Single phase half sinusoidal wave controlled rectifier with (? = 30?) pure resistive load (Vs =220 v. f=60 Hz, R=10Ω) Determine the average output voltage Vo  Determine the r.m.s value of the output voltage
4)Mark the correct statements: a) The frequency at the output of a half-wave rectifier circuit is 30 Hzb) The frequency at the output of a full-wave rectifier circuit is 60 Hz.c) To calculate the average voltage (DC) at the output of a full wave rectifier we use the formula: Ucc = 0.636 * Up.d) When using a bridged full wave rectifier, we know that the loss at the depletion barrier will be 2 * 0.7 Volts.e) None of the statements is correct.
3. The current supplied by a rectifier has a sinusoidal wave shape with a maximum value of 6.83 amp. What is the average current if the rectifier is of the (a) full-wave type, (b) single-wave type?
Q3] a three phase half wave controlled rectifier with resistive load (R-10 0) if the input supply voltage is (Vrms 380 Volt and f= 50 Hz) and the trigger angle (a 60°), then determine the followings:- a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforins. c) Calculate the average value of the output voltage.
Explain the operation of the diode in the full-wave bridge rectifier, the zener diode in a voltage stabiliser and the bipolar transistor as an amplifier. Please dont copy and try to answer in written on paper i will like
Describe the nature of the output voltage out of half – wave and full – wave rectifiers with that of the input voltage. D: O VoIE, AF GEN. RL 60 Hz / 100 Hz V./E. R1 2.2 k + AF GEN. RL 60 Hz / 100 Hz R2 2.2 k D2 b 10K
Calculations and Discussion Calculate the theoretical output DC voltage of the half-wave rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. Determine also the practical and theoretical values of the ripple factor.
Convert a dc voltage Q7)------ from one level and a certain polarity to a dc voltage of another level and in some applications to another polarity. Oa. DC-AC Converter Ob. AC-AC converter Oc. DC Chopper Od. AC-DC rectifier
Calculations and Discussion 1. Calculate the theoretical output DC voltage of the half-wave rectifier circuit when C=47UF and compare it with measured value. 2. Calculate the theoretical output DC voltage of the full-wave bridge rectifier circuit when C=100uF and compare it with measured value. 3. What value of filter capacitor is required to produce 1% ripple factor for a full-wave rectifier having a load resistance of 1.5kQ? Assume that the peak value of the output voltage is 18V.