Core uPMN turnsIn the system in the figure, magnet NdFeB,Br=1.25 T, Hc=-900 kÃ/m, N=100, i=20 A,Im=10mm, Core cross section=100mm2,T=200Ca) What is the magnet Hm value in kA/m?b) What is the core flux density, T?c) Calculate the winding inductance.d) How many Joules is the energy taken fromthe magnet for the given size and currentvalues?e) For T=1000C, if Bm=0.3 T, Hm=-600KA/mat the magnet corner point (knee point), whatis the current value at which demagnetizationstarts?

According to guidelines we need to solve only the first three sub-parts. According to the…

Core - PM Ntums In the system in the figure, magnet NDFEB, Br31.25 T, Hc=-900 kĀ/m, N=100, i=20 A, Im=10mm, Core cross section=100mm2, T=200C a) What is the magnet Hm value in kA/m? b) What is the core flux density, T? c) Calculate the winding inductance.

Core - PM Ntums In the system in the figure, magnet NDFEB, Br31.25 T, Hc=-900 kĀ/m, N=100, i=20 A, Im=10mm, Core cross section=100mm2, T=200C a) What is the magnet Hm value in kA/m? b) What is the core flux density, T? c) Calculate the winding inductance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: An 6-pole, wave-connected armature has 800 conductors and is driven at 625rev/min. If the flux per…

A: Given: A generator has, Number of poles, P=6 Wave wound so number of parallel path, A=2. Armature…

Q: For operation at 60 Hz and a given peak flux density, the core loss of a given core is 1W due to…

Q: A two-legged magnetic core with an air gap is shown in figure below. The depth of the core is 5 cm,…

A: The given magnetic core and graph are shown below:

Q: (a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in…

Q: 13.37 The double-excited electromechanical system shown in Figure P13.37 moves horizontally. Assume…

A: The doubly-excited system shown moves horizontally. The cross section of the structure is w X w.…

Q: Construct a Coil Winding (Armature winding) detailed, with these following descriptions.... 4…

Q: Example with 778 wave-connected armature conductors and run- ning at 500 rp.m. supplies a lood of…

A: Since there are multiple questions uploaded so solving the first question accordingly as per the…

Q: Draw the electrical circuit analog for the magnetic circuit shown in Figure P14.34. Pay special…

A: To draw the electrical circuit analog for the magnetic circuit shown in Figure P14.34. Now, to…

Q: 1. The armature of D.C. generator is laminated to (a) Reduce the bulk (b) Provide the bulk (c)…

Q: What characteristic is desirable in the B–H curve for a prospective material to be used in a…

A: In permanent magnet, the magnetic material in which the magnetic dipoles are already oriented in a…

Q: Derive the equation (Rule) step by step, to calculate the secondary induced emf of a static…

A: Consider the static electric machine is the transformer. Then, the emf equation of the transformer…

Q: From a technicians standpoint, how is the stregth of an electromagnet typically varied? a) by…

A: An electromagnet is a type of magnet in which the magnetic field is produced by an electric current

Q: Design a winding diagram given the following specifications. • Simplex Wave Progressive Winding •…

A: We need to design a simplex wave progressive winding for the following configuration: number of…

Q: The effective core length of a 6-pole dc machine armature is 40 cm and its diameter is 30 cm. This…

Q: The magnetic circuit shown in Figure P13.11 hastwo parallel paths. Find the flux and flux density…

A: Given values N = 1000 turns, I = 0.2 A, lg1 = 0.02 cm, lg2 = 0.04 cm, µr = 1 Expression of…

Q: Problem 1 In the following magnetic circuit, N = 1000; µ. = 1230. As shown in the figure, for the…

A: In every magnet, there will be a north and south pole. For a permanent magnet that has north and…

Q: (a) A 6 pole, 2 circuit, wave-connected armature has 250 conductors and runs at 1200 r.p.m. The…

A: The solution is as follows.

Q: Consider the magnetic circuit in Figure. Assuming that the core u= 1000uo has a uniform cross…

Q: 5) The magnetic circuit in the following figure has current 20 A in the coil of 5000 turns. Assume…

A: Given information i=20 A No. of turns, N=5000 Cross-section area, Ac=Ag=2 cm^2…

Q: Consider the magnetic circuit in Figure. Assuming that the core u= 1000uo has a uniform cross…

Q: A two-legged core is shown in figure below. The winding on the left leg of the core (N) has 800…

A: We have given the following problem A two legged core is shown below the winding on the left leg of…

Q: xplain why, when steel is subjected to alternating magnetization energy, losses occur due to both…

Q: In figure, a magnetic flux of F is generated with a constant current of i The core material used has…

A: Given: For a magnetic circuit, Number of turns of the coil N=400, Current in the coil i=20 A,…

Q: Compute the flux in each leg of the core shown in Figure P14.33. Account for fringing by adding the…

A: ∅ = Aμ(N1i1 + N2i2)/l For given problem, N1 = 1000 turns A = 2cm X 2cm = 4X10-4 m2 μ = 5000 i1 = 0.5…

Q: Determine the power output of a DC armature having 1152 lap connected conductors carrying 150 A and…

Q: Given a magnetic circuit as shown in Figure Q3(a)(i) where the core is a cast steel. B- H curve for…

Q: A two-legged core is shown in figure below. The winding on the left leg of the core (N,) has 600…

A: Given that, N1=600 N2=200 i1=0.5 A i2=1 A μ=1000 We have to find total flux

Q: ne function of a commutator is O change dc to ac O cuts the magnetic flux and emf is induced O…

Q: Explain why, when steel is subjected to alternating magnetization energy, losses occur due to both…

A: In this question we will find hysteresis and eddy current losses at given frequency....

Q: Determine the flux per pole for 6 pole dc machine having 240 wave connected conductors, which…

Q: Q4/ An 8-pole, tap-wound armatur rotated at 350 rpm is vequired to generate 260V. The useful flux is…

A: EMF generated in generator = flux×speed×number of armature conductors60×No. of polesno. of parallel…

Q: The B-flux is determined to be 52.35 mWb. If the material that surrounds this flux has a…

Q: A 4-pole, simplex lap wound armature when driven at 600 rpm generates 120 V. If the flux per pole is…

A: In this question we need to find a number of armature conductor.

Q: In induction heater, heat is produced in magnetic materials when they are exposed to an…

A: Choose the correct option The given statement In induction heater, heat is produced in magnetic…

Q: The toroidal (circular cross section) core shown in Figure below is made from cast steel. (a)…

A: Given toroidal diagram is - Given that material is cast steel so relative permeability is 4000.

Q: A toroidal core with a mean circumference of 100 cm and a cross sectional area of 10 cm2 is wound…

Q: Question one: The toroidal (circular cross section) core shown in Figure below is made from cast…

Q: Using Faraday's Law as a starting point prove that the maximum operating voltage of a transformer to…

Q: For a magnetic circuit, on no-load condition, core loss is, PC = 16 W; apparent power, (VA)rms = 20…

Q: A ferromagnetic core is shown in Figure Q5. The depth of the core is 5 em. The other dimensions of…

Q: Question 3 Current/ Consider the magnetic circuit of the following figure, Let the cross-section…

Q: For the toroidal core given below assume uniform flux intensity H over the core cross-section. Also,…

A: First find reluctance of the core. Coil inductance = N2/reluctance.

Q: What is the hysteresis loop for elastic materials? Explain the concept behind it briefly.

A: explain elastic hysteresis loop

Q: The figure shows a ferromagnetic core. The core depth is 5 cm. The other dimensions of the core can…

A: Write the expression for the reluctance,

Q: A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core…

Q: The magnetic relay in the figure has a coil of 500 turns currying a current I =4,19 A. The mean core…

A: First find reluctance of the core and airgap. MMF = NI. Flux = MMF / reluctance. Flux in the core…

Q: the total reluctance of the core in A.turns/wb is: none O 45873.5 206901.4 12254.33 486454 O…

Q: 13.a. Eddy-current loss in the stator core can be reduced by using A. alloys with low resistivity.…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

Core u
PM
N turns
In the system in the figure, magnet NdFeB,
Br=1.25 T, Hc=-900 kÃ/m, N=100, i=20 A,
Im=10mm, Core cross section=100mm2,
T=200C
a) What is the magnet Hm value in kA/m?
b) What is the core flux density, T?
c) Calculate the winding inductance.
d) How many Joules is the energy taken from
the magnet for the given size and current
values?
e) For T=1000C, if Bm=0.3 T, Hm=-600KA/m
at the magnet corner point (knee point), what
is the current value at which demagnetization
starts?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. -10 cm- - 20 cm- 15 cm 400 turns 15 cm 15 cm Core depth 5 cm
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
A flux of 0.0016 Wb flows in a silicon sheet steel coil/core. The arrangement appears as shown below with the following dimensions: Ac = 0.0025 m? Core/gap area: Flux path length: le = 0.350 m lg = 0.0015 m N = 500 Air gap length: Number of turns: %3D A. What is the current, I, through the winding? B. What is the energy stored in the inductance? C. Assume that the current is given by i =9.75 sin (3147) A. What is the RMS voltage that would appear across the winding? D. Assume that the gap is removed from the arrangement with the flux path remaining at 0.350 m. For a flux of 0.0016 Wb, what is the inductance of the arrangement? E. What is the energy stored in the inductance with the gap removed?
A ferromagnetic core is shown in Figure Pl-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 800. 1-5. 10 cm- 5em 20 em 15 cm 15 cm 15 cm Coe depth - Scm SOLUTION There are three regions in this core. The top and bottom form one region, the left side forms a second region, and the right side forms a third region. If we assume that the mean path length of the flux is in the center of each leg of the core, and if we ignore spreading at the corners of the core, then the path lengths are I, = 2(27.5 cm) = 55 cm, I, = 30 cm, and /, = 30 cm. The reluctances of these regions are:
5. A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800 а. 1.0 А c. 1.5 A b. 2.0 A d. 2.5 A
A magnetic circuit with a cross-sectional area of 20 cm? is to be operated at 50 Hz from a 120 V rms supply. The number of turns required to achieve a peak magnetic flux density of 1.8 T in the core is
2. AC-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the Reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm^2. Next find the flux flowing thru the C-core.
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
2. A two-legged core is shown in figure below. The winding on the left leg of the core (N,) has 600 turns, and the winding on the right (N2) has 200 turns. The coils are wound in the directions shown in the figure. If the dimensions are as shown, then what flux would be produced by currents i, = 0.5 A and iz = 1.00 A? Assume p, = 1000 and constant. -15 cm+ +i5 cm 15 cm 600 turns 200 turms 15 cm core depth- 15 cm [0.0054 Wb]
(a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in Figure 1. The depth of the core is 10 cm. The other dimensions of the core are as shown in the figure. By assuming the magnetic leakage to be negligible and relative permeability of the core is 800. Calculate the total reluctance and find the value of the current that will produce a flux of 0.01 Wb. With this current, calculate the flux density at the top of the core 20 cm 40 cm 10 cm, 30 cm 500 turns 30 cm 30 cm Figure 1
B. For the following magnetic circuit, the flux passing through the core is 1.32 mWb, the cross section of the core is 3 cm by 4 cm, the laminated section has a stacking factor of 0.9, and the gap is 1 mm. Determine the flux density in each section. Neglect fringing d N turns Cast iron Air gap Laminated sheet steel