Consider V= 11 V, the dependent source shown in the circuit given below is unfortunately installed upside down during manufacturing,so that the current arrow is pointing downward. This is not detected by the quality assurance team, so the unit ships out wiredimproperly. The capacitor is initially discharged. If the 5-0 resistor is only rated to 2 W, after what time t is the circuit likely to fail?+Vx10920.5vxwww592X= 020 μFThe value of t at which the circuit is likely to fail isVCUs.

Answered: Image /qna-images/answer/28b59250-c14e-4438-9131-59a456e76d54.jpg

Answered: Consider V= 11 V, the dependent source…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

What is CEMF?
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Value: Student No. Last 1 digit ( will be selected as kΩ, LastThose whose number is "0" get "9")a) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
A six stage Cockcroft Walton type DC voltage multiplier circuit has stage capacitance of 0.01 mF and supply voltage of 100 kV at a frequency of 100 Hz. It delivers and a load current of 1mA. It will have, what the value for follwing Qustion? 96 Voltage regulation Maximum output voltage possible Optimum number of stages No load voltage Voltage drop
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
Question 15 In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True False Moving to another question will save this response. ip
Consider the circuit shown in Figure Q7. The full-wave bridge rectifier is supplied from a transformer that has a secondary winding resistance of 52. When conducting, each diode has a forward voltage drop of 0.7 V, regardless of the current carried. D1 D4 240 V rms 50 Hz D2 D3 RL Figure Q7 (a) The transformer has a turn ratio of 10:1. Find the value of the load resistance, RL, if the peak voltage across the load is found to be 20.0 V. (b) For a load resistance of 50 2 and a transformer that gives a peak current in the load of 0.5 A, what is the power dissipated in the load? n:1
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
a. What is the effect of applying reverse voltage on a pn junction? b. What is the critical electric field and when will it happen?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS