Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at T. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA

Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at T. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 140-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA = 260 N-m. The shaft is machined from steel with Sy = 400 MPa and Sut = 560 MPa. Assume factor of safety and all other factors as (one) 1,. Determine the minimum allowable diameter of the 100-mm section of the shaft for infinite life (selectec criter sould be written at the begining of the solution) 250 mm 100 mm 20
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 320 N-m, Tc = 371 N-m, and TD = 181 N-m. TD (3) O -208 N-m O -224 N-m O -138 N-m O -190 N-m O -265 N-m Tc (2) B TB (1) TA
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at the bottom) to permit the use of a hand crank. Each flat is located 1.00 in from the center of the shaft. A torque of 750 Ib-in is applied. Find: (a) the maximum shear stress at the end of the shaft with two flats in psi unit. (b) the angle of twist in fadians (c) the angle of twist in degrees h= 1.0 in h= 1.0 in d= 2.50 in Show all your calculations.
The two solid steel shafts shown in the figure are connected by gears. Determine the angle of twist of end A of shaft AB when the torque T = 25 N - m is applied. The DC axis is fixed at D. Each axis has a diameter of 20 mm. G = 70GPa.
A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The bearing support between A and B allows free rotation. If we know that A = −0.382 rad, A/B = 0.358 rad, and B/C = −0.233 rad, calculate the absolute twist of the shaft at point C(oc) and enter it in rad (radians) correct to 3 significant digits below. Make sure to include the sign if it is negative noting that CCW rotations are positive and CW rotations are negative. 150 N.m 280 N.m B 40 N-m D
The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure. The journal bearings A and B exert on the shaft only the y and z components of the 100 mm 250 mm 50 mm support reactions. Dětermine the equilibrium torque T at gear C. Using the "Maximum 75 mm 150 mm Distortion Energy Theory" with Jallowable the together 80 MPa, smallest calculate possible diameter of the shaft millimeter that will support the loading. to the nearest 100 mm F.= 15 kN