Consider the stea dy flow of a fluid through a duct. The fluid density at t to the duct is 1000 kg/m and it is 998 kg/m at its exit. The duct has area of 0.05m? at its enterance and it is 0.04m at its exit. If the fluid ve enterance is 10m/ sec then the velocity at the exit of the duct is given E O About 10.48 m/ sec About 12.52 m/sec

Consider the stea dy flow of a fluid through a duct. The fluid density at t to the duct is 1000 kg/m and it is 998 kg/m at its exit. The duct has area of 0.05m? at its enterance and it is 0.04m at its exit. If the fluid ve enterance is 10m/ sec then the velocity at the exit of the duct is given E O About 10.48 m/ sec About 12.52 m/sec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Brine is flowing through a coil with a velocity of 240 fpm, The pressure foss in overcoming me traction in the coil 3.134 psia. The diameter of the coil is 3 ft and it has internal diameter of 1.20 inches At 86 degree Fahrenheit, the density of the brine is 995.6262 kg/m and its viscosity is 0.10081067 PA. a.) Calculate for the fanning friction factor in problem. b.) Determine the number of turns of the coil.
Consider the following figure showing a jet of water supporting a weight of 100 N at aheight of 5 m . Water leaves the nozzle with a velocity of 20 m/s. The diameter d ofthe nozzle will be
Air is accelerated in a nozzle. The mass flow rate in kg/s and the exit area in cm? of the nozzle are to be determined. (Express your answer: mass flow rate must be rounded off to three decimal places and the area in one decimal place.) V, - 20 m's 4- 60 cm" AIR V, = 150 m's Answer:
could you please help me calculate theheigth in metres of the fluid at time t= 100s
A water jet has a diameter of 75mm and ahs a velocity of 15m/s. What is the horsepower exerted by the jet. ANSWER: 10hp
pls replyyy Air is flowing through a square conduit whose section changes from 100 mm (section 1) to 200 (section 2). At section 1, v1=6 m/s and the density at section 1 is 1 kg/m3. If the velocity of flow is 1.8 m/s at section 2, find the density of gas at section 2
What is the water velocity (m/s) at point A? Here h-28.5 cm water A
can you please solve this for me thanks,The increase in flow energy of a 10 ft3 of fluid passing a boundary of a system is 80,000 ft-lb. Determine the exit pressure if the inlet pressure is 100 psi.
The pump is used to transfer fluid from one location to another of different height. At inlet and outlet atmospheric conditions are present. The pipe diameter increases after the pump outlet. Determine all the surviving terms of energy equation after simplification. FUM kinetic energy, potential energy, pipe losses none pipe losses, potential energy, pressure increase pressure increase, pipe losses, potential energy kinetic energy, pressure increase, pipe losses OOO
The Water is flowing through a pipe having diameter 350 mm and 210 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 25.85 N/cm? and pressure at the upper end is 11.6325 N/cm? & the rate of flow through the pipe is 40 lit/s. Draw a neat diagram and determine the following: 1.Velocity head at bottom of the pipe in m/s. 2. Velocity head at top of the pipe in m/s. 3. The difference in datum head between top & bottom in meter of water - 4. The difference of pressure head between bottom to top end in meter of water.- The velocity of flow of water at the bottom in m/s.
In some high-rise buildings, water is stored in an elevatedtank on the roof to minimize pressure fluctuations inthe system. Consider water that is pumped through a 10-cmsteel pipe to the roof of a 200-m-tall building; the pump ison the ground floor. For a water temperature of lOOC and aflow of 0.02 m3/s, what is the pressure at the pump discharge(in kPa)?
A cylinder with a mass 0.222 kg is sliding downwards through a vertically positioned pipe. A thin oil layer exists between the cylinder and the pipe's internal surface. Centerline of the cylinder and the pipe overlap. (yoil =8044.2 N /m3 ; voil=6-106 m²/s). Find the change in the speed of cylinder in the pipe with respect to its unit displacement and the shear stress that acts upon the oil layer. A A L = 128 mm V W 73.8 mm 74 mm 0.1 mm Figure 1