consider the rectangular cross sectional area shown in the figure below. if the bending stress at point P which is ( )cm away from the neutral axis is 88.9 MPa knowing that b = 98 cm and the moment of inertia of the entire cross sectional area is I = 10x10-° m then the maximum bending stress on the cross sectional area is a oP b O a. 266,7 O b. 133.4 O c. 177.8 O d. 222.2

consider the rectangular cross sectional area shown in the figure below. if the bending stress at point P which is ( )cm away from the neutral axis is 88.9 MPa knowing that b = 98 cm and the moment of inertia of the entire cross sectional area is I = 10x10-° m then the maximum bending stress on the cross sectional area is a oP b O a. 266,7 O b. 133.4 O c. 177.8 O d. 222.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the allowable bending stress is 0 = 165 MPa, find the magnitude of the maximum internal bending moment M₂ that can be supported by the beam. The moment of inertia about the z axis is 402,238,667 mm4. 16 mm 240 mm 352 kN-m O 243 kN-m 379 kN-m O 268 kN-m O 308 kN-m 30 mm 350 mm
The cross-sectional dimensions of a beam are shown. Assume b-2.125 in., tt-0.3125 in. and d=2.125 in. (a) If the bending stress at point K is 3360 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o, at point H (positive if tension, negative if compression). H N K Answers: bf (a) M₂ = i (b) σH = i d lb-ft. psi.
The cantilever beam is supported by a fixed support at A, and subjected to the force F = 550 lb and the couple M = 2870 ft-lb. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(x). Take x = 0 at point A. c 03O 2013 Michael Swanbom F CC BY NC SA M A • B a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 6.2 ft 4.34 ft Support Reactions The force reaction at A is lb (take up as positive). The couple moment reaction at A is lb (take counterclockwise as positive). Shear Force and Bending Moment Equations In section AB: V(x)= lb and 'M(x)= ft-lb. In section BC: V(x)= lb and 'M(x)= ft-lb.
Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft A to to D B- 8 ft 8 ft- -8 ft
for the figure shown below, what is the maximum bending moment, knowing that Ra=50 KN and Rb-70 KN 10 kN/m A 6 m 30 kN/m B 95.6 KN.m O 80.6 KN.m O other O 90.6 KN.m O
The cross-sectional dimensions of a beam are shown. Assume b=3.625 in., tetw=0.1875 in. and d=4.125 in. (a) If the bending stress at point K is 2470 psi (T), determine the internal bending moment M, acting about the z centroidal axis of the beam. (b) Determine the bending stress oy at point H (positive if tension, negative if compression). K d H Answers: (a) M2 = i Ib-ft. (b) oH = i psi.
The internal loadings at a cross section through the 120-mm-diameter drive shaft of a turbine consist of an axial force of 12.5 kN, a bending moment of 1.2 kN - m, and a torsional moment of 2.25 kN m. (Eigure 1). Figure 1.2 kN-m 12.5 kN 1 of 1 2.25 kN-m
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
A beam is supported and loaded as shown. In the section of the beam between 'A' and 'B', the equation for the resisting bending moment was determined as: M₁ = -6.5x²+50x. Determine the magnitude of maximum resisting bending moment (Mr,max) in the section. Note: Do NOT include units in your answer Answer: AA B
A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm. If there are no other loads applied to the beam (My, P, Vy and Vz = 0), what is the normal stress at point F? Give your answer in kPa to two decimal places with negative indicating compression and positive indicating tension. b/4 М, h E Ihis F h/3 В M. D b/4
2. Bending moment, M. is applied about z axis. If the normal stress due to bending moment at point A is (o,)-43MPA, determine (a) the applied bending moment, M; and (b) the normal stress at point B, (0,)B. 75 mm y TT 5 mm 50 mm B 40 mm 5 mm 5 mm
Consider an 8-m long simply supported T-beam with overhangs loaded as shown below. 200 mm w kN/m 50 mm 50 kN-m 50 kN-m 200 mm 2 m 4 m 2 m 50 mm 1. Determine the location of the neutral axis measured from the top of the beam and the moment of inertia (in mm4) of the section about its neutral axis. Draw the shear and bending moment diagrams. Annotate all relevant values and distances. Determine the magnitude of the maximum negative 2. moment. Determine the minimum allowable strength of the beam in tension and the minimum allowable strength of the beam in compression. 3. Determine the maximum allowable load, w (in kN/m), that can be applied pn the beam. 4. B.