Consider the following state table. Present Next State Output State X = 0 X = 1 Z A D C 0 B F H 0 E D 1 A E 0 C A 1 F B 1 B H 0 H с G 1 (a) Reduce the state table to a minimum number of states using implication charts. (b) Use the guideline method to determine a suitable state assignment for the reduced table. (c) Realize the table using T flip-flops. (d) Realize the table using JK flip-flops. CDEFGH с Ε

Consider the following state table. Present Next State Output State X = 0 X = 1 Z A D C 0 B F H 0 E D 1 A E 0 C A 1 F B 1 B H 0 H с G 1 (a) Reduce the state table to a minimum number of states using implication charts. (b) Use the guideline method to determine a suitable state assignment for the reduced table. (c) Realize the table using T flip-flops. (d) Realize the table using JK flip-flops. CDEFGH с Ε

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Use D flip-flops to design a mod-16 binary down counter, whose counting sequence is 1111->1110->1101->1100->1011-> … ->0000->1111…. Derive the logic expressions for the D inputs of the flip-flops and draw the circuit diagram.
Show how an asynchronous counter with J-K flip-flops can be implemented having a modulus of eleven with a straight binary sequence from 0000 through 1010 . Draw the diagram.(need only handwritten solution .otherwise downvote.)
Design a 4-bit counter C( represented by C3C₂C₁C₁)which can count the specified sequence as following: 0000011010010010 ➜ 11000000. The counter will use the falling edge of the clock (denoted by Clk) and have a separate reset pin (R) which will reset the counter to 0000 when it is low (e.g. = 0). Please use D type Flip-flops. Write down the state diagram, and state table; Use K-map to simplify the input equations; Write down the simplified input equations and draw a neat circuit diagram. (Hint: use don't care for unused states)
1) by creating the state table for the state diagram given below a) draw logic diagrams by designing Sequential Circuits with JK Flip flops. b)Draw logic diagrams by designing Sequential Circuits with D-Type Flip flops.
Design a 3-bit synchronous counter, which counts in the sequence: 001, 011, 010, 110, 111, 101, 100 (repeat) 001, ... Draw the schematic of the design with three flip-flops and combinational logics.
Design a 6-bit counter with control input using flip-flops. Every hour pulseIt should be a design that will increase or decrease by 4 when it arrives. Control input increment orwill determine the decrease. Increasing when control input is 0, decreasing when 1should be designed.
It will be designed as a flip-flop synchronous logic circuit with inputs P, N and having the following operating characteristics. Construct this flip-flop using a JK flip-flop and the required logic gates. In other words, design and draw the synchronous logic circuit that converts the JK flip-flop to this flip-flop.
Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
The state diagram is a basic 3-bit Gray code counter. This particular circuit has no inputs other than the clock and no outputs other than the outputs taken off each flip-flop in the counter. Show the state table, Karnaugh maps, and counter implementation using JK flip-flop.
We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
Use d flip flop to design the sequential circuit from state diagram. Draw truth table, k map and logic diagram.