Consider the following fluid power system components: valves, motors, compressors, and pneumatic cylinders. Discuss one of the components in detail. show a datasheet of the component and try to explain the specifications. How would you use the specifications provided in the design of a fluid power system? Discuss the range of applications and technical specifications, and if it requires any electrical control to operate.

Consider the following fluid power system components: valves, motors, compressors, and pneumatic cylinders. Discuss one of the components in detail. show a datasheet of the component and try to explain the specifications. How would you use the specifications provided in the design of a fluid power system? Discuss the range of applications and technical specifications, and if it requires any electrical control to operate.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter44: Four- And All-wheel Drive

Section: Chapter Questions

Problem 7RQ: When the plates of a viscous coupling (clutch) rotate at different speeds, the plates ____________...

See similar textbooks

Similar questions

Explain the working of Thermometer type transducer with a neat diagram to measure the Temperature. Draw the block diagram of a flow measurement system .Also identify the names of the functional elements used in the measurement system. Explain the working of XY type recorder with a neat diagram.
FLUID POWER TECHNOLOGY 7) For the hydraulic system of Figure 3, the following data are given: •The pump is adding 4 kW (pump hydraulic power) to the fluid. •Pump flow is 2000 cm3/s. •The pipe has a 25.4 mm inside diameter. •The specific gravity of the oil is 0.9. Determine the pressure available at the inlet to the hydraulic motor (station 2). The pressure at station 1 in the hydraulic tank is 1 atm. The head loss hL due to friction between stations 1 and 2 is 9.144 m of oil. (Hint: Use Bernoulli’s formula)
When the plates of a viscous coupling (clutch) rotate at different speeds, the plates ____________ the fluid.
please draw technical drawings of the pipeline of lubrication oil system in an ship engine room.
Give one example of an engine management system fault for each component Air-flow meters Temperature sensors And for each of the following: (5 - 10 words each Intermittent faults Multi-system faults Introduced as a result of a system repair Indirect, caused by the influence of external systems In your answer, briefly explain the process that would be followed to diagnose the fault.
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.
1. Define the 3 mediums used for automation (Pneumatic System, Hydraulic System, Electronic/Electrical System) and2. Discuss the advantages and disadvantages of each system. Include examples of where are this system is used.3. Differentiate the types of actuators (Pneumatic Cylinder, Hydraulic Cylinder, and Electrical Cylinder). What are the advantages and applications of each
A. How fast is the water going out of this pipe? B. What is the pressure of the liquid at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure. C. What is the maximum height the pipe can go above the drum before water stops flowing out of the pipe? For liquid flow to be continuous, liquid's pressure must not fall before its vapor pressure. Assume that vapor pressure in this case is 2.30[kPa].
The plot below shows typical data taken from pressure variations in a pressure vessel. Determine the maximum time between samples for a computer control system to be used with this system.
Show diagrams and calculations to support your answer. Suppose you are a group of cadet engineers given by your department manager a “simple” task of choosing an appropriate flow meter to install in a straight horizontal pipeline of the given specifications: Nominal diameter: 6 inches Schedule Number: 40 Material of Construction: steel Water is to flow through the pipeline within the range of 600 to 625 gal/min at a temperature of 27°C. You have the following choices in terms of the flow meter: [a] a venturi meter [b] an orifice meter [c] a rotameter [d] a commercial flowmeter of your choice, other than the above-mentioned ones Which would you recommend? Tips: [1] Base your choice on the following criteria: [1.a] pressure loss due to the presence of the flow meter [1.b] relative cost (and ease) of installation [1.c] relative cost of equipment
3. You are assisting a company that is installing new compressors and updating their pneumatic system. The company is interested in minimizing not only initial investment costs, but also costs of operation. A. What specific advice would you give them in their choice of compressors? B. What information would you need to determine the best method(s) of compressor-capacity control for improving the efficiency of the system during operation? Explain your answer.
Hide AnswerTry Another The formula for piston displacement is P = cd2SN, where c is a constant, d is the cylinder bore, S is the stroke, and N is the number of cylinders. For c = 0.7854, d = 3.000, S = 4, and N = 6, find the piston displacement. (Use the rules for working with measurements to give your answer to the appropriate accuracy and/or precision. Note: The values for S and N are exact numbers. Ignore exact numbers when determining the appropriate accuracy and/or precision.)