Consider the circuit of Figure. 1 for the case which R = R=14 as. The power supply has a de value of superimposed a 60HZ sinusoid of 2 V amplitude (Power-supply ripple). Calculate the de voltage of the diode and the amplitude of the sine-wave signal appearing across it. Assume the diode to have a 0.7 V drop at 1 mA current and n-2. ID]kn. a.7 V on which is

Consider the circuit of Figure. 1 for the case which R = R=14 as. The power supply has a de value of superimposed a 60HZ sinusoid of 2 V amplitude (Power-supply ripple). Calculate the de voltage of the diode and the amplitude of the sine-wave signal appearing across it. Assume the diode to have a 0.7 V drop at 1 mA current and n-2. ID]kn. a.7 V on which is

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

LANGIT 10. Design a suitable circuit to obtain an output waveform from a sinusoidal input of peak voltage 20 V. Assume germanium diodes 4.1V - 12.3 V
3.0 2 e) Find the Hotal resistance (R) of this circuit b) If the terminals la and c) are connected to a 24.0 V DC power supply, what 1s the total current I and the curreat passing through cach recistor ? ) Caleulate the correspending voltage dpop accros s tach resistor (labet acc ordingly: R,=6.00 Q, Rz ÷4.60 2 Ry= 8.002)
Q4. Determine the value of collector current and collector-to- emitter voltage for the voltage divider bias circuit Shown in Fig.2, .assume B = 100 %3D R, 10 k2 +10 V Rç 1 kO R2 5 kn RE 500 2 ww ww ww
Conduc-Thor-s. Thor has two square prism conductors that are made of the same ohmic material and with properties indicated below. Conductor Length Cross-Section Side Length Alpha Beta L/2 8/4 Suppose both conductors are subject to the same potential difference AV across their length while keeping their temperatures fixed. Which of the following is the correct relation between the electric currents, I, and Ig, through Aipha and Beta? O A. I = 81, %3D O B. 8I. = I3 Oc. Ia = 413 O D. 4la = I3
1. Determine the dynamic (ac) resistance of the diode at a forward current of 10 milliAmpere using the equation below. 26 mV r'd %3D ID The dynamic (ac) resistance (in ohms) is (put values only, put up to 2 decimal places)
Q3: Design a full-wave rectifier with Ik2 load. The rectifier operates from A.C supply of 220v (rms) and 50HZ through 20-to-1 step down transformer having a center tapped secondary winding. What is the peak value of the rectified output across the load and the fraction of a cycle does each diode conduct? What is the PIV of the used diodes. The diodes can be modeled to have 0.75v voltage drop for any current.
5. Find hall coefficient, electron density and the angle between the field, for a silicon wire with thickness 2mm, while the applied magnetic field is 0.1T, carying a current 10mA, hall voltage Imv and the mobility 0.36mNS.
1 (a) Using Townsend's second ionization criterion, consider I, 4 x 10-7 A. Consider a = 2.28/cm. If y = 0.0075, find the gap spacing dspark in cm for spark breakdown criterion. Calculate the current I in A for (i) d = 0.45 xdspark , (ii) d = 0.6 x dspark and (iii) d = 0.8 x dspark Show that the current I = Io exp (ad) when d is very small value and y is also very small value. 1,ead 1- y(ead – 1) (b) For a point-plane gaseous dielectric system, suppose values of a = 2.24 / cm and y = 0.0064. d Find the values of for d = 1.25 cm and d = 1.95 cm. dd
A single phase full wave rectifier has two diodes and the forward resistance of each diode is 25 ohms. The transformer secondary voltage from center to each half of the secondary winding is 30 2 V sin wt and the load resistance is 2000 ohms. Compute for the following: A. Average value of load current or the dc load current. B. rms value of load current, C. Peak inverse voltage of each diode
2. In this experiment, you will be finding a voltage at which the anode current is maximum. To find the voltage accurately you select the peak area of the data and fit it with a function of a form ax²+bx+c (parabola) as shown in the figure 3. The better way to write a parabola would be y = a(x-xo)² + yo. 25 y = -2.7526x2 + 103.02x- 943.68 R2 = 0.9774 20 10 15 20 25 Voltage (V) Figure 3: Determining voltage for maximum current Let's try to understand first how there two forms are related and determine the voltage value at which the maximum current occurs. Expand y =a(x-xo)² + yo and determine a (coefficient of x?) that а. involves a and/or xo and/or yo. b. Figure out b (should be a coefficient of x) that should involve a and/or xo and/or yo. с. Find an expression for x0 in terms of a and b. (Use the answers you got in a and b). d. Using the fitting equation on the graph find the value of xo. Current (A)
13 The surfoce temperature of the oun * is obout 6000 K. Accordingly which wovelenght corresponds to the greatest 15 value of the electro etic. rodiotion from the an? Interpret your reaul 16 occor ding to the sensitiuity ofhe humon. ge. 17 18 19
MOA silicon crystal diode has maximum allowable value of forwarder current is 634.3 mA. What is the forward power rating?