Consider the circuit diagram below, where the load is indicated by the dashed box. Compute the apparent power and power factor of the load. Use power factor correction to correct the power factor of the load to 0.9 lagging. Your solution should include a circuit diagram of your modified circuit. Rs ww C1 20 μF L1 1 H vs(t) 20 V 60 Hz RL 100 N +

Consider the circuit diagram below, where the load is indicated by the dashed box. Compute the apparent power and power factor of the load. Use power factor correction to correct the power factor of the load to 0.9 lagging. Your solution should include a circuit diagram of your modified circuit. Rs ww C1 20 μF L1 1 H vs(t) 20 V 60 Hz RL 100 N +

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25MCQ

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
A 400 MVA synchronous machine has H, = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two machines operate in parallel in a power plant. Find out H relative to a 100 MVA base.
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
What is the average Power at maximum resistance? Why? What is the effect to the voltage and current when increasing the load resistance?
For the circuit of the following figure, if R=26 0, Zc=-J26 0, and ZL=J30 0, and if the value of the nodal voltage V is 1.743-27 47° V, find the value of the reactive power supplied by the 3L-41 V voltage source. Ze R 15/24 V E ZL 341 V a 0.0377 VAR b.00736 VAR C0.0471 VAR d. 0.0589 VAR le
The power factor of the circuit shown in figure 2 is. a. 0.866 lagging b. 0.5 lagging c. 0.707 lagging d. 1
Resistive Voltage The supply across the terminals of this circuit is 170 V, 50 Hz. An ammeter is connected to the supply. ww000 R L The inductance L is 0mH. The ammeter reading the supply current shows 4 A. Find the magnitude of the voltage across the resistance: V. • Use Impedances and Complex Numbers. • Use Ohm's Law. Meters read Magnitude.