Consider an internal flow within a circular pipe as shown below. Pipe diameter, water mean inlet and exit temperatures with the mass flowrate is given with the figure. Please note that the figure is not scaled. water 64°C D= 5 cm 20°C 0.01 kg/s i- Calculate the length of the pipe, if it is heated with a uniform, constant surface heat flux of 300 W/m². Calculate the surface temperature at the exit of the pipe. 11-

Consider an internal flow within a circular pipe as shown below. Pipe diameter, water mean inlet and exit temperatures with the mass flowrate is given with the figure. Please note that the figure is not scaled. water 64°C D= 5 cm 20°C 0.01 kg/s i- Calculate the length of the pipe, if it is heated with a uniform, constant surface heat flux of 300 W/m². Calculate the surface temperature at the exit of the pipe. 11-

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

Consider a tank with surface area A.(m2) It containsa fluid of M(kg) at an initial temperature of T0. (C) The specific heat of the fluid is Cp. (J/kg) The fluid inside the tank is heated with condensing vapour outside at temperature of Ts. find the equation that gives the change of the temperature of the fluid in the tank with time.T=f(t) neglect donduction heat transfer h=heat transfer film coef. homogenous T through the tank
Consider the case of liquid flow in a uniformly heated channel. Initially, heat flux is so low that it only increases the liquid sensible heat. We then start to increase heat flux until water starts to boil. We keep increasing heat flux until eventually we attain a specific value for heat flux at which the tube first experiences CHF. Under this condition at what point does CHF first occur?
In an electric tea kettle filled with water, the bottom surface temperature is at 130 °C and has rounded surface with a diameter of 5 inches. Under standard atmospheric condition, how much will be the heat transfer flux q" at the surface and what is the mass flow rate of water vapor generation?
350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
Air at atmospheric pressure enters a heating duct with dimensions of 3 x 6 in. The air enters the 16 ft long duct with a temperature of 32 F, and the duct surface is maintained at 150 F. If the air exit temperature is to be 68 F, what is the air flow, in lb/hr? (answer in whole number) For air, R = 53.342 ft-lbf/lbm-R, k = 0.173 Btu-in/ft2-hr-F, and cp = 0.24 Btu/lbm-
b) A 0.4-W cylindrical electronic component shown in Figure Q3b with diameter 0.3 cm and length 1.8 cm is mounted on a circuit board is cooled by air flowing across it at a velocity of 150 m/min and temperature is 40 °C. Take the pressure of air 1 atm and the film temperature to be 50 °C, determine the surface temperature of the component. Resistor 0.4 W D= 0.3 cm Figure Q3b
Air at atmospheric pressure enters a heating duct with dimensions of 3 x 6 in. The air enters the 16 ft long duct with a temperature of 32 fahrenheit, and the duct surface is maintained at 150 fahrenheit. If the air exit temperature is to be 68 fahrenheit, what is the air flow, in lb/hr? (answer in whole number) For air, R = 53.342 ft-lbf/lbm-R, k = 0.173 Btu-in/ft2-hr-F, and cp = 0.24 Btu/lbm-
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. It will under compressible or incompressible criteria. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
Solve for the latent heat of water at Tw = 28C(and. λw = 2435 kJ/kg)
P1 D2 D1 The last 40 °C until the water vapor pressure in the tube shown in Figure 0.75t/m2d. Be that atmospheric pressure in the high current 68 cm-Hg-column, one section of diameter D60 em. the second section of diameter D = 14 cm, the first pressure value in the section P-0.35 kg / cm by that the cavitation neglecting the energy losses Determine the flow rate to start. system. Note: Use a period () as a decimal separator in your auswers. Otherwise, even if your result is correct, it will be considered incorreet by the 3. /sec im Q=
V(m/s) V(m/s) Q=2000 IIIIII air D-0.1m Air at (3.15x102) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (2.000x100) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 3/kg-K. Specific heat of air is 1000 1/kg-K Find the outlet temperature i 2000 J of heat is added to the pipe.
Describe the process of internal flow convection heat transfer in an annular tubeconcentric and draw