Consider a wood beam (see figure) carrying a uniform load of 18.5 kN/m (which includes the weight of the beam). The length is 2.75 m and the cross section is rectangular with width 150 mm and height 300 mm. 18.5 kN/m 300 mm 150 mm 2.75 m (а) 18.5 kN/m 2.75 m (b) (a) If the beam is simply supported as in figure part (a), calculate the maximum shear stress tmay and the maximum bending stress omay: (Enter the magnitudes in MPa.) MPa max = MPa Omax = (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress Tmay and the maximum bending stress omay: (Enter the magnitudes in MPa.) max = MPa max MPa %3D

Consider a wood beam (see figure) carrying a uniform load of 18.5 kN/m (which includes the weight of the beam). The length is 2.75 m and the cross section is rectangular with width 150 mm and height 300 mm. 18.5 kN/m 300 mm 150 mm 2.75 m (а) 18.5 kN/m 2.75 m (b) (a) If the beam is simply supported as in figure part (a), calculate the maximum shear stress tmay and the maximum bending stress omay: (Enter the magnitudes in MPa.) MPa max = MPa Omax = (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress Tmay and the maximum bending stress omay: (Enter the magnitudes in MPa.) max = MPa max MPa %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam shown in Figure below is simply supported symmetrically at two points 2m from each end and carries a uniformly distributed load of 5 kN/m together with two concentrated loads of 2 kN each at its free ends. 2 kN 2 KN w = 5 kN/m 2m+ 2 m 8 m 2 m Calculate the deflection in mm at the mid-span point and at its free ends. EI = 43×10¹2 Nmm² Umid span mm Vat end Round your answers to 1.d.p mm
A 1-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load q. The maximum deflection is measured as 2.5 mm. (Use available deflection formulas. All beams have constant flexural rigidity EI.) (a) Calculate the magnitude of the distributed load q (in kN/m) if the beam has a rectangular cross section (width b = 25 mm, height h = 50 mm). kN/m (b) If instead the beam has circular cross section and q = 500 N/m, calculate the radius r (in mm) of the cross section. Neglect the weight of the beam. mm
Consider a wood beam (see figure) carrying a uniform load of 21.5 kN/m (which includes the weight of the beam). The length is 2.25 m and the cross section is rectangular with width 150 mm and height 300 mm. 21.5 kN/m 300 mm 150 mm 2.25 m (a) 21.5 kN/m 2.25 m (b) i (a) If the beam is simply supported as in figure part (a), calculate the maximum shear stress max and the maximum bending stress max (Enter the magnitudes in MPa.) Tmax = MPa MPa max (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress max and the maximum bending stress max (Enter the magnitudes in MPa.) = MPa Tmax MPa max
EXAMPLE 6. A simply supported beam of span 20 m carries two concentrated loads 4 kN at 8 m and 10 kN at 12 m from one end. Calculate (a) the deflection under each load, (b) the maximum deflec- tion. E=200,000 N/mm2; I=10^9(mm^4)
A simply supported beam as shown in Figure (A) below, has the cross-section shown in Figure (B) with width of 200 mm and all depth of 300 mm with flanges and web thickness of 20 mm. Determine the maximum compression and tension bending stress which can setup in the beam. S kN 7 kN 2 kN 200mm 20 mm 4 kN/m 300mm 20 mm L Im J. I Im Im 3m 20 mm Figure (A) Figure (B)
Q.2) A simple beam of span length 3.2 m carries a uniform load of intensity 48 kN/m. The cross section of the beam is a hollow with wood flanges and steel side plates, as shown in the figure below. The wood flanges (E = 10 GPa) are 75 mm by 100 mm in cross section, and the steel plates (E = 210 GPa) are 300 mm deep. What is the required thickness t of the steel plates if the allowable stresses are 120 MPa for the steel and 6.5 MPa for the wood? 75 mm 75 mm C 100 mm 300 mm
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. a. What is the moment of inertia (in mm4) of the cross-section of the beam? b. What is the value of Q (in mm3)? c. What is the actual bending stress of the beam in MPa? d. What is the actual shearing stress of the beam in MPa?
2- For the beam in Figure below. a- Compute the immediate deflection produced by total load, b- Estimate the additional long-term deflection if the live load acts continuously. fe = 28 MPa, fy= 400 MPa. 手 Dead Load=27 kN/m Live Load =30kN/m 150 735 250 500 6 m 125 125 150 As=4 Ø 25mm
A simply supported beam of 6 m length, has 2 linearly varying loads each of span 3 m and both of load-intensity q N/m as shown in the figure below. The beam cross-section is a rectangle, with a triangle (height = 150 mm and base semi-circle (Radius = R mm) cut out from it, as shown in the figure. The beam is made up of material whose yield stress in compression tension = 250 MPa. At the section of maximum bending moment, the bending stresses at extreme fibers reach the allowable yield stresses simultaneously. Find: = 2R mm) and %3D %3D = 175 MPa and yield stress in %3D %3D a. The radius of semi-circle R (in mm) b. The load intensity of linearly varying loads q (in N/m)
The cantilever beam shown in the figure consists of a rectangular structural steel tube shape [E = 200 GPa;I = 95 × 10° mm*). For the loading shown, determine the beam deflection at point B. Assume PB = 14 kN, Pc = 50 kN, wAB 65 kN/m 16 kN/m, L1 1.5 m, and L2 = 3.0 m. ,WBC APB Pc WAB WBC B |C L, L, i mm VB =
The beam shown in the figure has a rectangular cross-section 4 inches wide by 8 inches deep. Compute the value of P that will limit the midspan deflection to 0.5inch. Use E = 1.5x10^6 psi. w = 2774 Ib/ft P P - 2ft 10ft 2ft Using Conjugate Beam Method: A cantilever beam having a span of 6m is subjected to a concentrated load of 244 N at a distance 3m from the fixed end. Determine the slope and deflection at the free end of the beam. Write your final answers in terms of El |
The triangle section AB beam, bearing the load F1 = 400 dan in the figure, is produced from a material with a maximum shear stress of 1800 daN / cm2. If the base length of this beam, which is forced to bend under F1 load, is b = 8 cm, how many cm should its height (h) be in order to carry this load 3 safely? (The weight of the beam will be neglected) F1=400 dan 300 cm 100 cm 38 - Davanım Momentleri W= Cm bh? bh? 24 d3 D* -d* b 10 10D b O A) 10,5 O B) 19,5 O C) 12, 25 O D) 15 O E) 17,25