Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cycle k is 0.5. The load is resistive with R-10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch-1V. The input power and the conduction losses in the switch are respectively equal to: Select one: a. 1272 W and 7.95W O b. 1264 W and 11.24W Oc. 1124 W and 11.24W Od. None of these

Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cycle k is 0.5. The load is resistive with R-10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch-1V. The input power and the conduction losses in the switch are respectively equal to: Select one: a. 1272 W and 7.95W O b. 1264 W and 11.24W Oc. 1124 W and 11.24W Od. None of these

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
Q1) The buck converter has an input of 50 V and an output of 25 V. The switching frequency is 100 kHz, and the output power to a load resistor is 125 W. Determine: (a) the duty ratio. (b) the value of inductance to limit the peak inductor current to 6.25 A. (c) the value of capacitance to limit the output voltage ripple to 0.5 percent.
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave.
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center- tapped full-wave and bridge type full- wave.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
a) Draw the basic topology of a buck converter. b) Design a buck converter to produce an output voltage of 18 V across a 10 2 load resistor. The output voltage ripple must not exceed 0.5 percent. The de supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. pls write legibly and show complete process of solution
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
An R-L load is connected to a 250 V, 400 Hz step down dc converter. The average load current is 100 A. The load resistance is 0.5 Ohm. The allowed ripple limit is 15%. The minimum value of inductor to limit the maximum ripple current is: