Consider a 50-mm-diameter and 25-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 30°C with a mass flow rate of 0.02 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet tem-perature of 170°C.

Consider a 50-mm-diameter and 25-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 30°C with a mass flow rate of 0.02 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet tem-perature of 170°C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.32P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
Consider a 50-mm-diameter and 25-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 30oC with a mass flow rate of 0.02 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet tem-perature of 170o
Water is flowing through a 25-mm diameter and 10-m long tube. The water enters the tube at 20\deg C with a mass flow rate of 0.2 kg/s. The outlet mean temperature is 60\deg C, and the tube surface temperature is maintained constant. Determine the hydrodynamic and thermal entry.lengths. Is the flow fully developed? What is the convective heat transfer coefficient inside the pipe?
Engine oil flows through a 25-mm-diameter tube at a rate of 0.5 kg/s. The oil enters the tube at a temperature of 25°C, while the tube surface temperature is maintained at 100°C. (a) Determine the oil outlet temperature for a 5-m and for a 100-m long tube. For each case, compare the log mean temperature difference to the arithmetic mean temperature difference.
Engine oil flows at a rate of 0.05 kg/s through a section of a 2.5 cm diameter tube. The oil enters the section at a temperature of 50 C. The tube wall is kept at 20 C, and it can be assumed that the flow through the section is fully developed. The section of the tube is 5 m long. (a) What is the exit temperature of the oil? (b) What is the heat transfer rate from the oil to the tube wall?
Heating Air by Condensing Steam.Air is flowing through a tube having an inside diameter of 38.1 mm at a velocity of 6.71 m/s, average temperature of 449.9 K, and pressure of 138 kPa. The inside wall temperature is held constant at 204.4°C (477.6K) by steam condensing outside the tube wall. Calculate the heat-transfer coefficient for a long tube and the heat-transfer flux.
Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The wall is maintained at a constant temperature of 210 by condensing steam. Fin the convective heat-transfer coefficient for this situation if the tube is 5ft long
Air at p = 1 atm enters a thin-walled (D = 5-mm diameter) long tube (L = 2 m) at an inlet temperature of Tmi = 100°C. A constant heat flux is applied to the air from the tube surface. The air mass flow rate is m = 110 x 10-6 kg/s. If the tube surface temperature at the exit is T = 160°C, determine the heat rate entering the tube, in W. Evaluate properties at T = 400 K. W Physical Properties Mathematical Functions
Liquid mercury at 0.5 kg/s is to be heated from 300K to 400K by passing it through a 50mm diameter tube whose surface is maintained at 450K. Calculate the required tube length by using an appropriate liquid metal convection heat transfer correlation. Compare your result with that which would have been obtained by using a correlation approximate for Pr > 0.7.
8.62, 8-62 Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.
Milk is Pasteurized by first heating it to 71oC, and keeping it at that temperature for 17 seconds before cooing it rapidly for bottling. Fresh milk at 5oC enters the Pasteurization unit where it flows through a thin-walled stainless steel (SS) tube of 2.0 cm diameter. The inside surface of the tube is such that the flow is turbulent to promote good mixing and uniform temperature across the flow at every point along the tube. Heating is provided by passing the tube in a closed container that is filled with saturated steam at atmospheric pressure and 100oC. Hence, we can assume that the thin-walled SS tube temperature is maintained at 100oC all along its length by condensing steam over the outside surface. The flow-rate of milk is 40kg per minute (i.e. approximately 10 gallons per minute). a) What is the mean velocity (m/s) and ??? for the milk flowing through the tube between 1-2? b) What is the convective heat transfer coefficient h (W/m2K) over the inside surface of the tube? c) What…