concrete -storey A penthouse was supposed condominium housing about 5,000 persons. The total height of the condominium is 25.50 m. The following data were gathered: Zone = 4 Soil Type = Unknown Seismic Source Type = C • Compute the total lateral force that the penthouse can support from the base in terms of its weight, Wp- Compute the total lateral force that the penthouse can support from the roof in terms of its weight, Wp

concrete -storey A penthouse was supposed condominium housing about 5,000 persons. The total height of the condominium is 25.50 m. The following data were gathered: Zone = 4 Soil Type = Unknown Seismic Source Type = C • Compute the total lateral force that the penthouse can support from the base in terms of its weight, Wp- Compute the total lateral force that the penthouse can support from the roof in terms of its weight, Wp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete building has 12 stories, each story is 3.2 m high. The facade column has 400 kN axial load per floor and a cross sectional area of 300mm×700mm. Calculate the shortening of the column at the ground floor level and the sixth floor when using concrete f'c= 25 N/mm and 40 N/mm?. Explain if there will be any effect on the facade.
A concrete block is supported by two guy wires attached to an anchor ring as shown. a.Determine the resultant force on the anchor ring. b.Angle of the resultant force with respect to the horizontal axis. c.Weight (W) of the concrete block with a factor of safety of 1.25 to prevent uplift.
Calculate the width of the concrete wall that is necessary to prevent the wall from sliding and the horizontal reaction acting on the system, Rx. The unit weight of the concrete is 23.6 kN/m^3 and the coefficient of friction between the base of the wall and the foundation soil is 0.42. Use 1.5 as the factor of safety against sliding. Will it also be safe from over turning?
Compute the total net deflection of the simply-supported beam with the following properties listed below. (Include the sign if it is negative) Properties: Length = 12 m Width = 334 mm Depth = 482 mm eccentricity = 136 mm %3D E 17,095.86 MPa Prestressing Force = 493 kN Unit weight of concrete = 22.25 kN/m³
A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor.
Figure 3.17 shows the elevation of two-storey building structures. The in-situ concrete floor is designed to carry an imposed load of 2 kN/m2 and ceiling finishes of 1 kN/m2. The floor slab overall depth is 250mm and the beams are simply supported. (a) Calculate the design loads acting on beams B-C/2 and 1-3/B by assuming the beam weight is 70 kg/m-run. For simplicity assume gravitational constant, gn = 10m/s2. (b) Propose the initial size for beam B/1-3 Check the suitability of section 406 x 178 x 67 UB for beam B/1-3 to carry the loads by conducting the following; (c) i) shear capacity (design shear resistance) ii) moment capacity iii) For the beam case, give some opinion on the shear force effect on the moment resistance. 3 3m 2 3m 3m 6m A (a) Floor plan
Problem 2. Determine the minimum height h of the beam shown in the figure if the flexural stress is not to exceed 20 Mpa. 1m 2.6 kN/m R₁ 6 KN 3 m 2 m R₂ 80 mm h
A: cantilever beam, 50 mm wide by 150 mm high and 6 m long, carries a load that varies uniformly from zero at the free end to 1000 N/m at the wall. Compute the magnitude of the maximum flexural stress.
A roadway sign weighs 7.2 kN and is supported by a structural pipe that has an outside diameter of 250 mm and a wall thickness of 11 mm. The resultant force of the wind pressure acting on the sign is 9 kN, as shown. Assume a = 8.2 m, b = 3 m, Pz = 9 kN, and %3D Py = 7.2 kN. (a) Determine the normal and shear stresses oH, TxyH at point H. (b) Determine the normal and shear stresses OK, TyzK at point K. a H K Answers: OH = i MPа. TxyH 28.6 MPa. OK i MPа. TyzK i ! MPa. II
A simply supported beam, 2 in wide by 4 in high and 12 ft long is subjected to a concentrated load of 2000 Ib. at a point 3 ft from one of the supports. Determine the stress in a fiber located 0.5 in from the top of the beam at midspan. O 2050.0 psi 1012.5 psi O 5062.5 psi O 2531.25 psi
3. A concrete framework is used to support a 125 mm reinforced concrete slab that carries a uniform live load of 12 kN/m?. The concrete density is 24kN/m³. The size of beam is 200 mm x 350 mm. There is a 125 mm thick brickwall on beam AD and CD. The walls are 3 m in height. Show the calculation of the design load of Column D in Figure 1. A 3m 5.5m Figure 1
a. Determine the largest distributed load value in lb/ft. b. Determine the point of inflection from A.