I will dislike for wrong answers solve carefully 3. A concrete rod with a cross-sectional area of 10 cm? is loaded in tension. Twocandidate concretes are: (a) a=1mm, p porosity=10% (b) a=3mm, p-5%.Determine the maximum (a) tensile force (b) compressive force on the concreterod before failure, respectively. Note that: E=(32GNIm 1-P andG. = (5KJ /m² )1 – p).

According to given data A concrete rod with a cross-sectional area of 10 cm2 is loaded in tension.…

Answered: -concrete rod with a cross-sectional…

-concrete rod with a cross-sectional area of andidate concretes are: (a) a=lmm, p=porosity=10% etermine the maximum (a) tensile force (b) compressive Note that: E= E=32GN

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Related questions

Q: The mass of oven dry aggregate per unit volume of aggregate particles, including the volume of perme...

A: The given statement is as follows: The mass of oven-dry aggregate per unit volume of aggregate parti...

Q: Determine the total length of curve, stations of Common Tangent and PC.

Q: Discuss two-way shear

A: A two-way shear, also known as a punching shear, occurs when shear is resisted along the edge of a m...

Q: Why do you think we do not place a fixed support in our in our trusses

Q: THE BEAMSSHOWN IN FIGURES (a) AND (b)HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPaAND IS SUB...

A: Given As =2×1000 = 2000mm2 D= 400mm, d = 350mm Since ?? ???????? < ???, So, tension steel yie...

Q: Determine the normal stress at the middle point H and at the corresponding point on the opposite sid...

Q: 4. (Problem 4.24 from the text book) A 60-N · m couple is applied to the steel bar shown. (a) Assumi...

Q: A waste water effluent of 560 lls with a BOD = 50 mgll, DO = 3.0 %3D mg/l and temperature of 23°C en...

Q: LEM 37: A sieel secion having a cross section of 20 mm x 30 mm is subjected to an axial force of 240...

A: To find Shear modulus

Q: Determine the Azimuth BC reckoned from North in Counterclockwise Direction. Note that the counterclo...

Q: An SPT test was performed yielding the following results. N1=14 N2=17 N3=21 The test had the follow...

A: Given:- The results for the SPT test are:- N1=14 N2=17 N3=21 Characteristics of the test are:- Type ...

Q: 45 m taped distance A surveyor used 75-meter line AB to compute his pace factor. The following are ...

A: The given data ,At day 3, the following are his number of paces for Line CD 517.00, 518.00, 521.00, ...

Q: 1,

Q: A copper rod of length L =18.0 in. is to be twisted by torques T (see figure) until the angle of rot...

A: Length of copper rod (L) = 18 in angle of rotation between the ends of the rod ϕ = 3° = 0.0523599 r...

Q: A square frame 3m x 3m in dimension is submerged in water vertically with its top 3m from the surfac...

A: Given data we have a square frame of 3mx3m , submerged in water vertically with its top 3m from th...

Q: A thin-walled tube is subjected to torsion as shown. Determine the Perimeter of the median line, S. ...

A: t=25mm L-6m r-300mm θ=80o T=4 kNm G=70 kN/m2 S-Perimeter?

Q: A rectangular timber having an actual width of 71/2 in and an actual depth of 111/2 in servers as a ...

Q: The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Compute t...

Q: (Problem 4.16 from the text book) The beam shown is made of a nylon for which the allowable stress i...

A: We will find neutral axis and permissible stresses.

Q: e AB has a width of 1.5 m and m. Determine the horizontale ical components of reaction

A: According to given data Plate AB has a width of 1.5 m and a radius of 3 m. To , Determine the horiz...

Q: In figure below, what is the pressure in pounds per square inch at A?

Q: Estimate the average depth of precipitation over the catchment. You are NOT allowed to use any compu...

Q: What is the percent passing on 4.75 mm sieve? b. What is the fineness modulus of the fine aggregate...

A: To find out the percentage passing on 4.75mm sieve and fineness modulus of fine aggregates.

Q: i may use following er -25kPa Cu 1.0-0.5 50kPa

Q: 4. AX kN load will fall from a height of W/5 m. Assume El = 400 x 1010 Nmm2. %3D (X kN „W, kN/m W/2,...

Q: ent whose shape can be approximately described b ng coordinates (distances in kilometres): (80, 10),...

A: According to given data station 1 co ordinates annual (0-40) rainfall (cm) 132station 2 co ordinate...

Q: wrw/m A B Sdve for locehen of Amex fram 1 A b) A max 6)

Q: 100kN 20kN 2° -80KN -100kN 2 m 2 m 1 m 3 m

Q: Situational Problem 5 (For Q16-Q20)A completely restrained beam having a span length of 4m with a un...

Q: Define Design Principles

A: Designers use design principles to apply widely applicable laws, guidelines, biases, and design cons...

Q: 600 kN/m Situation 7 (A) (CE Board May 1999) A propped beam A having a span of 6m carries a uniform ...

Q: Draw the internal axial force diagram (AFD), shear force diagram (SFD), and bending moment diagram (...

Q: The 60 cm pipe conducts water from reservoir A to a pressure turbine which discharges through anothe...

Q: A hollow cylinder 80 cm long in diameter, one end closed, is immersed vertically with its closed end...

Q: Congestion mitigation policies can themselves influence the "timing" of rural space. (A) True B) Fal...

A: The statement is TRUE. CONGESTION MITIGATION ALLOWS THEM TO provide jam free traffic , crowded free ...

Q: 2. Determine the pressure in a vessel of oil (sp gr 0.85) at a point 15.xy feet below the surface, e...

Q: A simply supported beam, 6m in length, has an initial deflection of 0.50mm at midspan due to its own...

Q: Problem 3: The pressures at the inlet and exit of a water turbine are 300 and 90kPa, respectively. T...

Q: A 1 m 2.5 m 8 m

Q: The light right-angle boom which supports the 540-kg cylinder is supported by three cables and a bal...

Q: Determine degree of static indeterminacy

A: We have to determine the value of degree of indeterminacy of the frame given in the question.

Q: The radius of a curve is twice its tangent distance, if the degree of curve is 6° calculate the angl...

A: The radius of a curve is twice its tangent distance, if the degree of curve is 6° calculate the angl...

Q: Following is the result of a modified proctor test. Determine the maximum dry unit weight, void rati...

A: SOLUTION: Given, the values of volume of mold = 0.000945 m3 weights of moist soil and moisture conte...

Q: What is the relevance of geology in Geotechnical Engineering? (Minimum of 7 sentences)

Q: emperature when this system was assembled was 74F, what would be the stress in a temperature of 4OF?...

A: According to given data The assembly below will be used for each problem Lengths, diameters, and ma...

Q: 2. A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and ...

A: Given Data: The side of a cube is b = 4 in. The specific gravity of kerosene is 0.82. To Determine...

Q: Derive the hydraulic exponent N by using the Chezy formula. a. Find the final form of N for trapezoi...

Q: A steel loop ABCD of length 1.2m and 12mm diameter is placed as shown around a 22mm diameter aluminu...

Q: Given an axial failure stress of 2000 psi, a factor of safety of 1.67 and modulus of elasticity 1800...

Q: A hypothetical metal alloy has a grain diameter of 2.4 x 10-2 mm. After a heat treatment at 575°C fo...

Concept explainers

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.

Question

I will dislike for wrong answers solve carefully

3. A concrete rod with a cross-sectional area of 10 cm? is loaded in tension. Two
candidate concretes are: (a) a=1mm, p porosity=10% (b) a=3mm, p-5%.
Determine the maximum (a) tensile force (b) compressive force on the concrete
rod before failure, respectively. Note that: E=(32GNIm 1-P and
G. = (5KJ /m² )1 – p).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 2: If f = 3 ksi what is the modulus of elasticity Ec and the maximum tensile stress fr that the concrete can carry before cracking (use ACI recommended equations). Assume a unit weight of the plain concrete is: a. Wc = 90- b. w lb lb 118- ft39 ft3) C. W = 160- Problem 3: Wight 3-6 Rugblom 4: Wight ? 7 lb ft3
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
The properties of the reinforced concrete beam are b = 303 mm, d = 466 mm, Ast = 1138 mm2, and Est / Eco = 9. If the working stresses are 18.5 MPa for concrete and 117 MPa for steel, determine the corresponding bending moment (in Nm) for the concrete. Round off the final answer to two decimal places. -b- h ΝΑ Ast (total area) d
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
Problem 1: Transformed Moment of Inertia and Elastic Deflection Given: The center of the top and bottom rebars are placed 2.5" from the top and bottom faces. Top Reinforcement: 2 no. 4 Rebar Bottom Reinforcement: 4 no. 9 Rebar Use textbook table A-1 for rebar properties Es = 29,000 ksi Ec = 3,600 ksi Unit weight of plain concrete = 145 lb/ft³ a. Find the transformed moment of inertia of the composite section. b. Calculate the reinforcement ratio p where p is Asb/bd. Asb is the area of the bottom steel, d is the depth from the top face of the beam to the bottom steel, and b is width of the beam. 16" c. A 30' simply supported beam has this cross-section. Ignoring the effects of cracking, how much would the beam deflect under its own self-weight and a live load of 0.64 kip/ft? d. Often the unit weight for reinforced concrete is assumed to be 150 lb/ft³. Repeat part c. using this assumption. e. Repeat part c. using the gross moment of inertia. Note: the gross moment of inertia is the…
The properties of the reinforced concrete beam are b = 308 mm, d = 486 mm, Ast = 1366 mm2, and Est / Eco = 10. If the working stresses are 18.8 MPa for concrete and 106.7 MPa for steel, determine the largest bending moment (in Nm) that may be applied safely. Round off the final answer to three decimal places. -b- d ΝΑ Ast (total area)
F 1. The "slump" test is used to determine the compressive strength of a concrete. (F) 2. For room temperature and axial loadingaluminum behaves as a brittle material. T. T 3. Proper curing is important for a concrete specimen to gain compressive strength. T. (F 4. Concrete usually has a good tensile strength. T F 5. The units of the modulus of elasticity are the same as for axial stress. T F 6. Plasticity is characterized by return of a ħaterial to original size & shape upon removal of stress. т F 7. Strain hardening increases the elastic strength of the material. T F 8. Some materials do not exhibit a well defined yield point. T F 9. The failure behavior of our aluminum specimen in our torsion test was expected. T F 10. Necking of a steel specimen loaded in tension is an example of Poisson's ratio.
Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. =10cm? E, = 2*10°kg /cm? E = 2*10 kg /cm f'. =1836kg / cm? 90 cm 100 cm 40 cm
Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. A = 10cm² %3D E, = 2*10°kg / cm² E = 2*10°kg / cm² %3D %3D f'. =1836kg / cm² %3D 90 cm 100 cm 40 cm