Answered: center-to-center spacing of struts in…

Engineering

Civil Engineering

center-to-center spacing of struts in the plan = 5

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.24CTP

See similar textbooks

Related questions

Q: 1.5m= D ↓ 20 kN/m² 71-18 kN/m² 41-30 ₁=0 (2) 0.5m → 4 0.7m (3) * C -0.7 m-0.7 m 2.6 m O P, H₂=6 m P.…

Q: Ex: The figure below is a proposed weir floor with three vertical piles. calculate the uplift…

Q: Design a support system with the struts are located at 3.5 m center to center in the plan. Given: y…

Q: Q2: The anchored sheet pile shown in Fig. 2 is constructed to permently raise the ground level by…

A: Earth pressure is the force exerted on the backfill on any structure retaining by backfill. Cohesive…

Q: In Problem 14.6, assume that Dactual = 1.3 Dtheory.a. Determine the theoretical maximum moment.b.…

A: a} Determine the value of z 12σ1'L1-F+σ1'z-L1+12Kaγ'z-L12=0F=Anchor force for unit length of the…

Q: 2. For the purposes of calculating the maximum stress in a braced cut, what are the primary factors…

Q: A 5 m wide braced excavation is made in a saturated clay, as shown in Figure P19.1, with the…

A: Solution Given Data c=20 kN/m2ϕ=00γ=18.5 kN/m3

Q: Q1- Use Rankıne theory to calculate the lateral earth pressure and determine the stabilıty of the…

A: Solution: For lateral earth pressure: Kac=cos2ϕ - ηcos2ϕ - ηcosη+δ1+sinϕ+δsinη-βcosη+δcosη-β1/22sub;…

Q: A vertical sheet pile supports a horizontal backfill having a height of 6 m. The backfill has a unit…

A: The required depth D of penetration will be :

Q: For the data given in Problem 13.5, calculate the lateral pressure σ'a at z = 2 m, 4 m, 6 m and 8 m.

A: Solution Calculate the effective horizontal stress σ'a at depth z=2m, 4m, 6m, and 8m Calculate…

Q: Using . =0 analysis and assuming planar failure as shown, the minimum factor of safety against shear…

Q: Refer to the braced cut shown below. Given: unit weight = 17 kN/m3, Friction angle = 35degrees, and…

Q: Figure below shows the cross-section of an excavation which is to be made alongside a river. Write…

A: To find -Depth to which water in the trench can be reduced before instability occurs.

Q: A 11.8 m long cantilever sheet pile retaining wall is to be used to support the 6.2 m deep…

A: The given information is By using Rankine method we have to find out the horizontal effective…

Q: A vertical sheet pile supports a horizontal backfill having a height of 4.5m. The backfill has a…

Q: Question attached

A: Draw the diagram

Q: An anchored sheet-pile bulkhead is shown in Figure P14.10. Let L1 = 2 m, L2 = 6 m, l1 = 1 m, γ = 16…

Q: Determine the analytical embedment depth and the total wall depth for this conditions. Give the…

A: step 1-

Q: Design a support system with the struts are located at 3.5 m center to center in the plan. Given: y…

Q: EX: A hydraulic structures shown in fig. determine 1- the correction of uplift pressures at key…

A: Correction for the uplift pressure at key points is given asC%=t·ϕ1-ϕ2dwhere t- thickness of the…

Q: Determine the depth of penetration of the wall into the silty clay soil and the maximum bending…

A: Given data : ∅'cs = 27°iL = 0.025i = 0.025 × 2.5 = 0.0625mSu = 50kPa Moment about K is given as,…

Q: Figure P14.1 shows a cantilever sheet-pile wall penetrating a granular soil. Here, L = 4 m, L2 = 8…

A: Sheet piles are metal parts with interlocking edges driven into the ground to provide permanent or…

Q: 3 m CLAY 1.5 m A 2.5 m 8 m 2.5 m 1.5 m

A: Shallow excavation or the surrounding soil can be supported by the piles driving into the ground…

Q: (a) Determine the forces acting on struts A, B and C for the braced excavation in stiff, fissured…

A: Given:- The spacing of the struts A, B, & C = 4 m center to center The cohesion of the soil = Cu…

Q: A vertical sheet piled wall is shown in Fig. below, the properties of the soil both behind and front…

Q: Question 2. In Figure 2, let L1= 4 m, L2 5 m, and l1 =2 m. Also, let y 17 kN/m³, Yat = 20 kN/m², o'…

Q: The slopes of the piles of loose granular material are stabilize by constructing the retaining walls…

A: The height of the retaining wall is H=7.5 m. The bulk unit weight is γ=18.1 kN/m3. The saturated…

Q: P-3 Refer to Figure, for which L, = 2.4 m, Sand L2 = 4.6 m, y = 15.7 kN/m³, Ysat = 17.3 kN/m³, and…

Q: Determine (a) the lateral earth pressure distribution for the braced cut analysis (including shape…

Q: A braced cut, 5 m wide and 7.5 m deep is proposed in a cohesionless soil deposit having effective…

A: brace cut : width = 5 m depth = 7.5 m effective cohesion (c') = 0 effective angle of friction (phi)…

Q: The cross section of a braced cut supporting a sheet pile installation in a clay soil is shown in…

A: Sheet piles are sections of sheet steel with interlocking edges that are driven into the ground to…

Q: Assuming a sheet pile wall is constructed to retain 12.5m of soil, as shown in Figure 2, and the…

Q: 1.21 Refer to Figure 11.35b. Let L = 15.24 m, yal 19.49 kN/m², ø'lay = 20°, H, = 3.05 m, and D (pile…

Q: a. The sheet-pile section modulus, assume that Gan = 170 x 10° kN/m² b. The required section modulus…

A: The lateral pressure of braced cuts in the sand is given by σa=0.65γHKa Ka = tan245-ϕ2= tan245-402=…

Q: A cantilever sheet pile wall is supporting a horizontal backfill having a unit weight of 18 kN/m3 .…

Q: The length of a horizontal floor is 14 m and a 3.5 m deep vertical sheet pile is attached at its D/S…

A: Given, length of the floor =14 m depth =3.5 m sheet is attached to D/S end Head of the water =4 m…

Q: b) Design an anchored sheet pile bulkhead as shown in Let L1 = 4 m, L2 = 9 m, I; = 2 m, y = 17…

Q: A circular pile having a diameter of 0.35 m is embedded through a layer of 4.5 m thick of clay layer…

A: D = Diameter of pile = 0.35 mH1 = Thickness of clay layer = 4.5 mH2 = Thickness of sand layer =…

Q: A new underground tunnel section is designed by a geotechnical consultant. For the underground…

A: Given, c= 20kN/m2 ϕ=0γ=18.5 kN/m2γHc=18.5×720=6.47>4

Q: 2. Assuming a sheet pile wall is constructed to retain 12.5m of soil, as shown in Figure 2, and the…

A: i)Calculating the pressure at the top: σv=6.7 KN/m2Pa=Ka1σv-2cKa1Ka1=1-Sin 101-Sin…

Q: PROBLEM NO. 2 A cantilever sheet pile wall is supporting a horizontal backfill having a unit weight…

A: Unit weight of soil (y) = 18KN/m3 Friction angle ( Φ ) = 30° Back fill height (H) = 3m Coefficient…

Q: 1. Figure 3 shows a cantilever sheet pile wall, determine the: Sand 3 m y = 16 kN/m3 O' = 30 Sand…

A: As the figure shows the different values at different depth position:

Q: Úpstream the Sheet pile wall 7 m Downstream 2 m

A: Given that....

Q: The braced cut of two layers of clay is shown in the f H; = 3 m; y1 = 14 kN/m³¸ c; = 25 kN/m? H; = 3…

A: According to given data

Q: Determine the forces on the struts for the braced excavation in soft, normally consolidated clay. 15…

A: Given data:B=4MH∘=6mL = 4mH∘B=64=1.5BL=44=1Thickness of firm layer Df= 7.5mThickness of failure…

Q: Problem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here,…

Q: 15.12 Determine the embedment depth, d, and maximum bending moment for the cantilever sheet pile…

A: We have to determine the embedment depth d and maximum bending moment for the cantilever sheet pile…

Concept explainers

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.

Question

Given:

γ =17.5 kN/m³
c = 30 kN/m²
center-to-center spacing of struts in the plan = 5 m.

Determine the sheet-pile section modulus for the braced cut.

Use σ _all = 170 MN/m²

6 m
I1m
(1 m
A
3 m
c = 30 kN/m²
$ = 0
y = 17.5 kN/m³
В
%3D
%3D
2 m
C
1 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SOLUTION. Wo = 6.16 kN/m L = 5.17m EI y = ? A 7/2 LLLLLLLL Wo 4 4₂
1.GIVEN: The vessel is initially full. Do = 200 mm %3D C = 0.8 REQUIRED: Time to empty the vessel. 15 m. 10 m 1.6 m 1.4 m As
a=4 mb=7 kN/m
X=9.0 kN. Y=4.0 kN/m
Solve the value of Ely at x = 2m. 6 kN 2 kN/m 4 kN A 3 m -1.5 m-1.5 m O -106kNm^3 O -148.67kNm^3 O -124.83KNM^3 O 103.33kNm^3
H.W. 1 4.0 m- 1 m 3.6 m A =? 2 m P = ? -2.0 m T = ? 17.0 m 1.2 m 7.0 m 0.90 m Z1 3.0 m
2 . 1 X I. 1 · 2. 11 | . 13 .I. 12 Give an example problem in relation to soil compaction and dry weight of soil. Dry Weight oi Suil W2 W3= m (6) 100 where: W3= dry weight of soil W2=weight of the moist soil excavated from the hole = moisture content %3D 9:39 AM P Type here to search 26°C Mostly sunny a 4) 9x) a ENG 06/10/2021
Consider two independent events A and B, where p(A) =0.4 and p(B) =0.1- Then p(ĀnBis equal to: Oa. 0.04 Ob. 0.36 Oc. 0.54 Od. 0.90 and. Not enough information provided to do the calculation
W1 = 10 KN/m a = 2m b = 3m
MA=43.5 kN.m B1 VB2 X *₁* x₂ = M B R₁ = 28.31 KN V A M X1 w = 6 kN.m D 8m Mp X2 2° R = 28.69 KN 3 E MB KN KN kNm kNm B 32 3 m V B1 2° 3° с
Example-1 10 - Figure 8.4a shows a 20 B1 typical cross section near the center of a gravity 20 B2 dam. Analyze the block 60 B1 for stability. Assume 20 B3 Тое zero freeboard. Heel la) Cross section of dam FIGURE 8.4 Analysis of a gravity dam. 3:10 6:10 Batter 1:20
92 25° 3.0m 9₁ = 300 kN/m 3.0m A 3.5m Ao₂