4- Cartilage reduces stresses applied to bones by:Decrease the force transmitted from the bone.a)b)c)d)e)Increasing the area of contact between articulating surface.Increasing the effect of friction.Building a non-homogenous load distribution.All of the above5- Which of the following statements is not true:Stress-strain diagram of each material can explain different mechanicalproperties (hardness, stiffness, ductility, brittleness ...).b)a)Stress-strain diagram can show the yield and the ultimate strengths ofthe material

Cartilage reduces stresses applied to bones by Increasing the area of contact between articulating…

Cartilage reduces stresses applied to bones by: a) b) Decrease the force transmitted from the bone. c) d) e) Increasing the area of contact between articulating surface. Increasing the effect of friction. Building a non-homogenous load distribution. All of the above Which of the following statements is not true: а) Stress-strain diagram of each material can explain different mechanical properties (hardness, stiffness, ductility, brittleness...). b) Stress-strain diagram can show the yield and the ultimate strengths of

Cartilage reduces stresses applied to bones by: a) b) Decrease the force transmitted from the bone. c) d) e) Increasing the area of contact between articulating surface. Increasing the effect of friction. Building a non-homogenous load distribution. All of the above Which of the following statements is not true: а) Stress-strain diagram of each material can explain different mechanical properties (hardness, stiffness, ductility, brittleness...). b) Stress-strain diagram can show the yield and the ultimate strengths of

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Read the question carefully and give me both A&B right solutions otherwise leave it. A) Steel Alloy rod made of Stainless Steel 304 is subjected to 60 kip of Tensile force. Steel rod is having diameter of 1 in. and Length of 8 in. Determine change in its length and diameter. Consider material behaves elastically. For determining material properties use Mechanical property table. B) An aluminium specimen made up of 6061-T6 Material has a diameter of d = 20 mm and a gage length of L0= 300 mm. If a force of 135 kN elongates the gage length 0.9 mm, determine the modulus of elasticity. Also, determine contraction of diameter.
A) A circular rod with a gage length of 3.6 m and a diameter of 2.3 cm is subjected to an axial load of 51 kN . If the modulus of elasticity is 200 GPa , what is the change in length? B)A circular rod with a length of 4 m and a diameter of 2.4 cm is subjected to an axial load of 61 kN . If the resulting change in length is 3.34 mm , what is the modulus of elasticity? C)A circular rod with a length of 3.7 m and a diameter of 2.7 cm is subjected to an axial load and increases in length by 3.26 mm . The initial portion of the stress-strain curve of the material is given. What is the applied load?
Question Three a) A wire 3m long and 2mm in diameter when stretched by weight of 10kg has its length increased by 0.28mm. Find the stress, strain and Young Modulus of the material of the wire. (g = 9.81m/s²) b) A steel column is 3.5m long and 0.4m diameter. It carries a load of 50MN. Given that the modulus of elasticity is 200GPa, calculate the compressive stress and strain, and determine how much the column is compressed.
A) A circular rod with a gage length of 3.6 mm and a diameter of 2.3 cm is subjected to an axial load of 51 kN . If the modulus of elasticity is 200 GPa , what is the change in length? B)A circular rod with a length of 4 mm and a diameter of 2.4 cm is subjected to an axial load of 61 kN . If the resulting change in length is 3.34 mm , what is the modulus of elasticity? C)A circular rod with a length of 3.7 mm and a diameter of 2.7 cm is subjected to an axial load and increases in length by 3.26 mm . The initial portion of the stress-strain curve of the material is given. What is the applied load?
a)Define the following mechanical properties which can be derived and, in each case, state the appropriate unit. i)Engineering stressii)Yield stress leveliii)Young’s modulusIv) Ultimate tensile stressv)Ductilityvi) Toughness B) Briefly describe a standard test method which can be used to establish properties (ii), (iii) and (iv) mentioned in part (a) of this question. Also provide a sketch of the apparatus.
Modulus of rigidity is defined as the: Select one: a. Area under the elastic zone of shear stress-strain diagram b. Slope of straight line in elastic zone of shear stress-strain diagram c. Slope of straight line in elastic zone of normal stress-strain diagram
2- A piece of muscle specimen has the initial length of 30mm and square cross section with original side of 12 mm was tested using a tensile test. The applied tensile force of 20 N resulted in deformation (AL) of 10mm.The muscle remained in the elastic deformation region during the test. a) Determine the modulus of elasticity of the muscle specimen (make sure to include stress (ơ) and strain (ɛ1ong)in your answers) b) If the side of square cross section measured at the maximum longitudinal stretch was 10.5 mm, determine the Poisson ratio of the muscle specimen c) Determine modulus of rigidity (G) (Ans: E=0.4167 MPa, v=0.375, G=0.1515 MPa)
Question 3 Determine the tensile stress in each cable given that all the cables have a cross-sectional area of 4cm?. Take mass of cylinder = 60kg; and acceleration due to gravity, g = 9.81 ms². A 45° B D
For a viscoelastic material, stress is not only a function of strain, but also a function of a. None of these b. Strain rate C. Lateral strain d. Young modulus TOSHI A
Q6: The following stress-strain curve is for a copper alloy (Figure 1 and Figure 2). At fracture, the total length was 53 mm, and the diameter was 10 mm. The initial length and diameter were 50.8 mm and 12.8 mm respectively. Determine: a) the 0.2% offset yield strength b) the ultimate tensile strength UTS c) the modulus of elasticity E d) engineering stress and strain at fracture e) true stress and true strain at UTS f) true stress and true strain at fracture (N) Load (N) 60000- 50000 40000- 30000- 20000 10000 0- 40000- 30000 20000 10000- 04 10 15 20 Change in length (mm) Figure 1. Load-Al curve for a copper alloy 0 5 0.2 0.0 Change in length (mm) Fracture region Figure 2. The magnified load-Al curve for the same above copper alloy to show the elasticity
Question 8. The following figure represents three hardness-testing techniques of materials. Describe their specifications, how there are conducted and their potential applications? 8 - Shape of Indentation Test Indenter Side View Top View Load Brinell 10-mm sphere P of steel or tungsten carbide Vickers Diamond 136° microhardness ругamid Rockwell and 60 kg) 100 kg } Rockwell 150 kg) Diamond 120° superficial cone: s - in.- diameter Rockwell 15 kg 30 kg } Superficial Rockwell 45 kg) steel spheres
Can anyone give a step by step for this? No idea how to approach. Thank you! The dimensions of a 3003-H14 aluminum rod at 1.0 inches in diameter x 15 inches long. a) What force is required to stretch the bar elastically long the length to 15.010 inches. b) What is the diameter of the bar at this load? c) What is the true stress in the material at this load.