Calculate the vertical reaction at B. Let P = 14 kips and W = 2 kips/ft %3D Assume A is a roller and B is a pin. Note: 1. Answer in whole number 2. Indicate the Minus sign (-) if answer is negative. For positive answer "no need" to write the (+) sign. P W 8 ft 7 ft- 7 ft 7 ft-

Calculate the vertical reaction at B. Let P = 14 kips and W = 2 kips/ft %3D Assume A is a roller and B is a pin. Note: 1. Answer in whole number 2. Indicate the Minus sign (-) if answer is negative. For positive answer "no need" to write the (+) sign. P W 8 ft 7 ft- 7 ft 7 ft-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Use Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28…

A: Shear force: Shear force is the resistance against sliding of the beam or it is the algebric sum of…

Q: the vertical reaction By as the redundant. AE is constant. D 30 kips 15 - 20' 20

Q: Determine the resultant reaction in D in kN using slope deflection method or moment distribution…

Q: 2. Determine the reactions (approximately) of the beam shown below. Use moment distribution method.…

A: Find support reaction using Moment distribution method.

Q: a = 3.2 m, b = 33.5 kN/m, c = 24 kN. ç kN b kN/m A BỊ DO "a" m 4 m 3 m FIGURE 2

Q: Calculate the vertical component of the internal force at B. Let W = 2 kips/ft. and P = 22 Note: 1.…

Q: Solve the problem using slope deflection method. Note: Show complete solutions and free body…

A: Given A beam Required Support reactions Shear force and bending moment diagram

Q: The force of magnitude Facts along the edge of the triangular plate. Determine the moment of F about…

Q: Using Moment Distribution Method, determine the reactions and draw the shear diagram. 3 k/ft 2 k/ft…

Q: An indeterminate beam carries concentrated loads as shown in the figure. Using any method you like,…

Q: 22.7 kN, b = 46.1 kN, c = 2.5 m, d = 5.1 m, e = 3.5 m kN C F cm EN E H K d m A D G e m e m

Q: PAGE DATE 13 K Ak/fb 2 k/ft to 10 10 10' 20' El=Constant

Q: Using Principle of Virtual Work Method. Determine the displacement in mm of point B of the steel…

A: Introduction- Virtual work is possibly the most helpful and broadly applicable of the deflection…

Q: Using the Moment Distribution method, calculate the reactions at th supports of the rigid frame…

Q: Example 10: The box wrench in Figure (a) is used to tighten the bolt at A. If the wrench does not…

Q: Determine the minimum force P to prevent the 399-kg rod AB from sliding. The contact surface at B is…

A: Take moment about B:∑ MB=0NA3+fA4-mg42=0NA3+0.45NA4-399×9.8142=0NA=1630.9125N

Q: Determine the reactions for the given figure below using. Use E = 200 GPa and I = 210 x 10° mm4 Use…

Q: a) If the beam AD is loaded as shown in Figure Q4(a), determine the horizontal force P which must be…

A: Determine horizontal force P?

Q: Determine the distance of the point of maximum positive moment from pt. C in m. Note: In your…

A: Given a beam of length 4mThere are uniformly varying load and a moment on beam.left support is…

Q: In the figure, suppose that 0 = 30°, V1 = 100 ft/s and the stream is a jet of water with an initial…

A: ρw = 62.427lb/ft3 V1 = 100ft/s V2 = 95ft/s Q = V1 x A = 100xπ/4x(2/12)2 = 2.18166ft3/s

Q: H.W.3: For the beam shown in Figure El = 100,000 kip-ft² and use discontinuity functions to…

A: Continuous beam: If more than two supports are provided to the beam, it is called a continuous beam.…

Q: An overhang beam carries a concentrated load, triangular load and uniformly distributed load as…

A: Given liad w=180 KN/m ans a=1.8 m and b=4 mmoment at roller B MB=-2700 kN.m…

Q: RM 300 ↓ 1m

Q: USE MOMENT DISTRIBUTION METHOD. Given the indeterminate beam, find the reaction at B in kN. EI is…

A: Find reaction at B in KN

Q: n the figure 9, assume clockwise moments as positive, force F= 432KN nd force P =500 KN. Calculate…

Q: 15 kN 3.4m 4.8m 67 7.2m 9 kN/m

Q: 4 kips 10 kips 2 kip-ft D A 2' 2' 6' 2' 30°

Q: The speed of water passing through the elbow on a buried pipe is V = 8 ft/s. Assume water is ideal…

A: Linear Momentum: The product of mass and velocity of the fluid is known as the linear momentum of…

Q: Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L = 4.3…

Q: H.W.4: For the propped cantilever beam shown in Figure assume that El = 100,000 kip-ft and use…

A: ∑Fy=0By+Dy=125×10+5×12=85 kips ...........1∑MD=0125×10+20+103+5×12×14-20By+MD=0MD-20BD=1423.33…

Q: L/3 m PKN Lm Q kN/m

Q: Determine the reactions of the indeterminate frame shown below using Slope-Deflection Method. Show…

Q: (Mc) C. a. Determine b.Determine d. Determine the tangential deviation at point B with respect to…

A: In order to find the reaction at R , we will make the beam as primary beam by removing R from the…

Q: The uniform 25 Ib-f ladder in the figure below rests against the smooth wall at B, and the end A…

Q: Question 6 Determine the moment at C for the beams shown using the three-moment equation. Express…

Q: 150 kN В D C 10 m 20 kN/m A 5 m -5 m

A: slope deflection method is displacement method. here slope and deflection are unknown. by getting…

Q: P = 25KN P2=38 kN 3.4m 4.1m w = 12 kN/m 12m 2.8m A

Q: Determine the reactions of the indeterminate frame shown below using Slope-Deflection Method. Show…

Q: Question 42 Determine the reaction at each support using slope deflection method. El is constant. 20…

Q: Horizontal reaction of support C. (NOTE: If the direction is going to the left, then put a negative…

Q: A 4m propped beam carries a distributed load that varies from zero at point A and "w"kN/m at point…

Q: Determine the forces in the x and y direction and the moment that must be applied at section 1 of…

A: The force acting on the pipe and nozzle assembly are a result of: Change in momentum of the flowing…

Q: below, the me end moments using the mo method. Then calculate the reaction forces and plot the axial…

A: Distribution factor at junction D. Stiffness of members; KDE=4EILDC=4EI20=0.2EIKDA =…

Q: The horizontal force P = 64 N is applied to the upper block with the system initially stationary.…

Q: Determine the support reaction at C using Conjugate Beam Method. Indicate the negative sign if the…

A: Consider the given figure \ Consider F.B.D

Q: 1- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a wall as…

A: Given: Tension in string = 50 N Reaction at A and B is 1.3KN and 433N Weight of ladder = 250N…

Q: c kN b kN/m 10 kN/m B. "a" m 3 m

Q: A 2m propped beam carries a distributed load that varies from zero at point A and "w"kN/m at point…

Q: A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine…

Question

Note: Answer in whole number. Draw and label the FBD properly

Calculate the vertical reaction at B. Let P = 14 kips and W =
2 kips/ft
%3D
Assume A is a roller and B is a pin.
Note: 1. Answer in whole number
2. Indicate the Minus sign (-) if answer is negative. For positive answer "no need" to write the (+) sign.
W
B
A
-8 ft 7 ft- 7 ft+7 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

EXAMPLE (1) A circular bar having 200 mm' area is subjected to axial loads as shown in Fig Find the value of ( P) and the total elongation . Take E=2*10'N/mm'. A 50KN 50KN d. lokN IM IM IM
Homework H20.B Given: The quarter-circle block A (having a weight of W) is supported by wedge B. The weight of the wedge can be considered to be negligible. Find: Determine the minimum force P on the wedge that is required to lift the block. Write your answer in terms of W. Use the following: us= 0.2 and 0 = 20°. P Hs R smooth wwwwwwwwwwwww
What is the value of the Horizontal reaction force at A in N? if P = 45-N. (Note: enter your numeric answer only. No need to enter units. Give your answer to three decimal places and negative in the left direction). Ax = N -2 m D -2 m- E 1.5 m A B.
8. 3 The deflection profile y(x) is given by emb A horizontal beam of unit length under load w(x) satisfies the system: y" = M, M" = w(x), x = (0, 1). free もエ 12 Find which end is embedded and which end is free. Find the load w(x). y y(x) = x¹ log(x) - OR free 4 = WCX) 25 еть x4 +4x³ - 3x². еть face y(0) = 0 y" (0) = 0, y !!! (o y' (8) = 8 (0) ) =
PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The machine part ABC is supported by a frictionless hinge at B and a 10° wedge at C. The coefficient of static friction is 0.20 at both surfaces of the wedge. The force Pis applied on the wedge to push it to the right. Given, F= 680 N. F 200 mm B -250 mm Problem 08.049.c - Reactions at hinge D The value of the component By Is The value of the component By Is [ 10° Determine the components of the corresponding reaction at B N (Click to select) N(Click to select)
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assume I = 800 x 106 mm and E = 70,000 MPa. F W1 BO C D 8 m 8 m 4 m 4 m w1 (kN/m) | F (kN) S (mm) Set A (1,2,3,4,5) B (6,7,8,9,0) 20 60 25 25 50 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 3. Reaction at A, RA in kN. (10 pts)
P(kN) = 187 1. Using DIM, solve for: a. Ymax (mm) b. A (rad) Use E = 200 GPa. 165 kN Yang A 1mO m B P 2m 1m 2m C D 90 kN/m 1m 2m E F 120 kN.m G Dimensions are in mm 200 80 400 300 50 50
SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool. 100 325 120 120 120 Dimenaions in millimeters Q Zoom image Determine the vertical force reaction under leg A. O 0.667L O 0.233L 0.533L 0.166L
Upvote will be given. Please write the solutions legibly. Solve in 2 decimal places. A simply supported 5-meter beam is an S- Beam, S610 x 119. If the beam has no external load, A. What is the reaction of the hinge support of the beam? Express the answer in Kilo-Newton? B. What is the reaction of the roller support of the beam? Express the answer in Kilo- Newton.
NEED ANSWER ASAP!! The 16 x 22 x 25 mm rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 313 N causes the upper frame to be deflected downward by 4 mm. Determine the shear modulus G of the rubber blocks.
Problem 3 The beam shown below is subjected to the loads shown in the figure. Use the moment-area method to determine the displacement at point 16 kN.m -6m B + -3m- C Note: Give your answers in terms of "EI" (constant for the entire beam). Note: A = pin, B = roller support
The 420-N force is applied to the 82-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.60 Hk = 0.44 Answer: F= i 30° N P = 420 N