B4 Calculate the compression resistance in kN of the cross-section of a stockyuniversal beam (UB) acting as a strut and not subject to buckling, given that;A = 67 cm?S355 steelYMO= 1.0tf = 14.8 mm (thickness of flange)Give your answer to the nearest whole kNDo not include units in the answer box.

Answered: Image /qna-images/answer/27f3ec71-5a99-4ffd-b49e-5207a314fb80.jpg

Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB) acting as a strut and not subject to buckling, given that; A = 67 cm2 S355 steel YMO= 1.0 tf 14.8 mm (thickness of flange) Give your answer to the nearest whole kN Do not include units in the answer box.

Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB) acting as a strut and not subject to buckling, given that; A = 67 cm2 S355 steel YMO= 1.0 tf 14.8 mm (thickness of flange) Give your answer to the nearest whole kN Do not include units in the answer box.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.6.21P: A steel plate (called a cover ploie) having cross-sectional dimensions 6,0 in. × 0.5 in. is welded...

See similar textbooks

Related questions

Q: 1. The composite bar in Figure below is firmly attached to unyielding supports. Compute the stress…

Q: Considering the effects of the prestressing forces (assume no loss) and the working loads (include…

Q: (8) A structural steel l-beam is 15m long when installed at 200C. How much will its length change…

Q: A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P,at its lower end.…

A: Given Data The load acting at point E is: P=2.5 kip Distance from A to B is: AB=20 in Distance from…

Q: A Steel Shaft 50 Mm Diameter And 500 Mm Long Is Subjected To A Twisting Moment Of 1100 N-M. If The…

A: Answer: ◆ The modulus of rigidity for the material of the shaft 73.5 GPa. ◆ The tensile stress…

Q: 3. Find the ratio of crippling loads by Euler's and Rankine's formulae for a hollow strut of 40 mm…

A: d0=40 mm di=30 mm I=π64404-304I=85902.924 mm4σyt=300 MpaE=200 Gpaa=17500

Q: For long column of length L, what will be the ratio of P, where, P1 Euler's buckling load, when both…

A: Data given-

Q: Q4: A cantilever beam of carbon steel is subjected to a load P varying from -50 to 150 N. Determine…

A: When external load on a component is not static, but varying in magnitude with respect to time, such…

Q: Example (13) A load of 300kN is supported by a short concrete column of size 250mm square. The…

Q: flat steel bar, 29 mm wide by 4 mm thick and 1.2 m long, is bent by couples applied at the ends so…

Q: A wooden mast, with a uniform diameter of 30 cm, is built into a concrete block, and is subjected to…

A: The maximum load that can be applied to the wooden mast can be determined as,

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area…

A: To find: The horizontal deflection of end C relative to end A. Given: The cross sectional area of…

Q: The frame shown in Figure 5 is unbraced, and bending is about the x-axis of the members. All beams…

A: 1. Calculate the ratio of column stiffness to girder stiffness at each and of column AB by using the…

Q: A composite shaft ABCD made of three parts is placed between two walls, as shown in Fig. 7. Part AB…

A: GIVEN: TO FIND:

Q: : By using LRFD method, select a W10 shape for column GH shown in figure for the following data: W=…

Q: Example 16.1. A solid round bar 60 mm in diameter and 2.5 m long is used as a strut. One t the strut…

A: When one of the column is fixed and the other end is hinged, then equivalent length of beam is…

Q: flat steel bar, 27 mm wide by 5 mm thick and 1.7 m long, is bent by couples applied at the ends so…

Q: Q.1. A T-section 150 mm×130 mm×30 mm is used as a strut of 5 m long with hinged at both ends.…

A: First, you need to calculate the effective length of the strut in both boundary conditions (both…

Q: A weight of 120ON is dropped vertically at the middle of a beam 50mmx250mm * and 6m long simply…

A: Find the height of weight that must be dropped from.

Q: 27 mm wide by 3 mm thick and 1.3 m long, is bent by couples applied at the ends so that the midpoint…

Q: Q4: A cantilever beam of carbon steel is subjected to a load P varying from -50 to 150 N. Determine…

A: When external load on a component is not static, but varying in magnitude with respect to time, such…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

Q: A protective type flange coupling is used to connect two mild steel shafts to transmit P kW at N…

A: P=46 kW ,N=198 rpm ,L=104 mw=1748 N, τmaxallowable=44 Mpa…

Q: At a cross section in a rectangular beam with b=300 mm and d=500 mm, flexural reinforcement is 5T20.…

A: Calculate the area of the steel. 5T20 means,n=5 and d=20 mmthen,As=5×π4d2=5×π4202=1570.8 mm2…

Q: Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB)…

Q: QUESTION line theory. , Calculate the collapse load (W collapse) for the slab shown, using the yield…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force…

Q: A cantilever beam made of carbon steel of circular cross-section as shown is subjected to a load…

Q: A flat steel bar, 29 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: Given Data: The thickness of the bar, t=3 mm Length of the bar, L=1.7 m Modulus of elasticity,…

Q: 10∙1 A rectangular plate 0.5 m long, 0.25 m wide and 10 mm thick is simply supported at the edges.…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MP ,…

Q: W 3 M M

A: Assumption: - The bone is considered to be a cantilever beam of the hollow section. The weight of…

Q: 1.10 The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate…

Q: A hollow compression member with circular cross section having outer diameter 2 times the inner…

Q: 16.11 Rigid beam ABC is supported by a pinned connection at A and by a timber post that is pin-…

Q: to a load that varies from -F to +4F as ne below figure. The length of the beam and it has a…

Q: 15 Q6) An aluminum bar having a cross-sectional area of (50.265 cm2) carries the axial loads applied…

A: Given, Cross sectional area = A = 50.265 cm2 = 50.265 x 10-4 m2 Yound modulus = E = 10 x 106 N/m2…

Q: The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and…

A: given; ⇒length of bar (L)=0.8m=800mm⇒bar dimension =150mm*10mmso;⇒width (b)=150mm⇒thickness…

Q: A cantilever beam of circular cross-section is made of alloy steel is subjected to a fluctuating…

A: Given: σmax = 48 N/mm2 σmin = - 24 N/mm2 FOS = 2 Syt = 0.55 Sut σe = 0.45 Sut

Q: Q4: A cantilever beam of carbon steel is subjected to a load P varying from -50 to 150 N. Determine…

A: When external load acting on a component is not static, but varying in magnitude with respect to…

Q: Calculate the maximum ultimate bending moment in the slab. Write your final answer as whole number…

A: Maximum Ultimate Bending Moment = 380229×21300×100×415 = 2.025 MPa

Q: Q1-A frame shown in figure (1) is loaded by a force of (100 N), the cross section area of the base…

A: Consider the Free Body diagram: The 100 N force is resolved in X and Y directions. The Y component…

Q: cross-s t- 5MM h= 10HM 100MM 100MM E=207 GPa W= 1200K A bar with 300 mm long between supports carry…

A: Given: The depth of the cross-section, h = 10 mm The width of the cross-section, t = 5 mm The length…

Q: Example/ A slab of steel in circular section with diameter 0.02m ane length 0.4m exposed into a…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MPa,…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Calculate the compression resistance in kN of the cross-section of a stocky
universal beam (UB) acting as a strut and not subject to buckling, given that;
A = 67 cm?
S355 steel
YMO= 1.0
tf = 14.8 mm (thickness of flange)
Give your answer to the nearest whole kN
Do not include units in the answer box.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
A steel plate (called a cover ploie) having cross-sectional dimensions 6,0 in. × 0.5 in. is welded along the full length of the bottom flange of a W 12 × 50 wide-flange beam (sec figure, which shows the beam cross section). What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
MA MB= Mc= MD= Required information For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=50 lbf/in and V2 = 7 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Hinge = 1400 lbf/ A BI AC R₂ R₁ 4 in 4 in 2 in V1 Determine the values of the moments at points A, B, C, and D. lbf.in lbf.in lbf.in Ibf.in V2 D R₂
Read the question carefully and give me right solution according to the question.. Please answer all. Don't miss anything. Figure 5 shows a rigid horizontal beam ABCE which is supported by a pair of rectangular bars CD at C. The cross-sectional size of each of the rectangular bar is 37.5 × 12.5 mm. Modulus of elasticity of the bar is E=80 GPa. Vertical loads of 17.5 kN and 35 kN act at points B and E, respectively.Compute:i) Vertical displacement of point Bii) Vertical displacement of point EIf it is given that the allowable displacement of point C is 1 mm, determine the minimum thickness of rectangular bar CD required. The width of the rectangular bar should be kept unchanged at 37.5 mm.
A beam is simply supported and has a span of 12 m. The beam is a W33×240 with Ey=345 MPa. Compute the following: A. If the compression flange has lateral support only at its ends. Express your answer in kN/m. (ASD) B. If the compression flange has lateral support only at its ends. Express your answer in KN/m. (LRFD) Properties of W33×240: Weight = 3.51 kN/m tw, = 21.08 mm rx = 352.54 mm A = 45,548 mm? Ix = 5,660.75 × 10° mm ry = 92.34 mm d = 850.9 mm ly = 388.34 × 10® mm* Jc = 14.51 x 106 mm* %3D bi = 402.97 mm Sx = 13,322.68 x 10° mm ris = 105.92 mm t = 35.56 mm Sy = 1,933.67 x 10° mm3
The simply supported W8X24 A-36 steel beam AB is loaded as shown in the figure. What is the slope of point B in radians if w = 5.7 kip/ft, L 16.5 ft, Mo = 6.2 kip-ft? Note: Your answer should include units and be to 4 decimal places. Mo Aरू 늘 -
The strut on the utility pole supports the cable having a weight of P = 300 lb. (Figure 1) Figure 1.5 ft -2 ft- 4 ft 1 B < 1 of 1 2 in. HT I4 in. Part A Determine the absolute maximum bending stress in the strut if A, B, and C are assumed to be pinned. Express your answer in kilopounds per square inch to three significant figures. omax = Submit Provide Feedback VO VE ΑΣΦ AΣ vec Request Answer ? ksi
For the beam shown, use only singularity functions. V₁ = 45 lbf/in and V/₂ = 5 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 0 1400 lbf Hinge JA B₁ C R₂ R₁ 4 in 4 in 2 in V1 V2 D R₂ + What is the value of the peak moment between points Cand D? The peak moment between points C and Dis Ibf.in.
The link shown, made of steel with y-410MPa and E-200GPa is subjected to a tensile load of 30kN. Let (h=6b). Assume the factor of safety is 2. a) Determine the dimensions of the section with the design based on yield strength. b) If this link, which is 40cm long, must not elongate more than 0.12mm, what should be the dimensions of the cross section? L F F -h b