Calculate the available net positive section head NPSH in a pumping system if the liquid density p 1200 kg/m'. The liquid dynamic viscosity u 0.4 Pa.s, the mean velocity u= 1 m/s, the static head on the suction side z = 3m, the inside pipe diameter di, = 0.0526m. the gravitational acceleration g 9.81 m/s, and the equivalent length on the suction side EL. = 5.0 m. The liquid is at its normal boiling point. Neglect entrance and exit %3D losses.

Calculate the available net positive section head NPSH in a pumping system if the liquid density p 1200 kg/m'. The liquid dynamic viscosity u 0.4 Pa.s, the mean velocity u= 1 m/s, the static head on the suction side z = 3m, the inside pipe diameter di, = 0.0526m. the gravitational acceleration g 9.81 m/s, and the equivalent length on the suction side EL. = 5.0 m. The liquid is at its normal boiling point. Neglect entrance and exit %3D losses.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil flows through a 16 tube single cooler with a velocity of 2 m/s. The internal diameter of the tube is 30 mm and oil density is 0.85 gm/ml. Find the volume flow in liters per sec. Answer asap plss. Thanks. I will rate helpful
Find the Base Temp at Airflow=0.1 m/s. it's an exponential relation. will upvote if correct.
Example 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is posted
dp 1. It shows that the behavior of fluid is A From the equation stated, show the formula for mass flow rate AVp = c. :C.
Centimuity oquation ofastendy frow. Terriellis problemfontflow of liquid througha hole) Problem:Detemine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, t=60°C. Static pressure in the tank p.=266,8 mmHg. Wedge resistance coefficient Sw=1,5, pipe inlet resistance coefficient Çin=0,5, the height of the oil level in the tank above the pump inlet section н-1,2 м, оil 1-12. H кран насос
02 h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump moves water @10°C from a lake into a large, pressurized holding tank as shown. The flow rate, Q. is 375 L/min, and the piping system losses, 1) Sketch the setup (simple schematic is good), 2) label the z datum, and 3) identify and label the boundary conditions (P, V, and z) at 1 and 2 for use in a) the General Energy Equation (GEE). Provide values and units for the boundary conditions. Hint: For identifying good locations for boundary conditions, where are the velocities approximately zero? b) Calculate the head added to the fluid, h,, by the pump. Give your answer in units of m. Hint: Be careful with signs in manipulating the GEE. Show as many steps as you need to get your h, equation correct. Calculate the power added to the fluid by the pump in units of kW. () Determine the required electric motor size to drive the pump in units of HP. Prank = 200 kPa Holding Tank Air 6 m Pump Lake
Centrifugal pump has differential pressure 15 bar and use to transport oil between two separators. If the pressure at first separator is 4 bar calculate the pressure at second separator and NPSH. Where: Suction and discharge pipe diameters = 10 inch, Suction pipe length = 16 m, ld Oil level at first separator 3 m2d Oil density=880 kg/m³ P Oil flow rate=0.092 m³/sec e Pipe roughness= 0.045 mm Discharge pipe length = 25 m O Oil level at second separator = 5.5 m2d Oil viscosity = 9.5 x 10³ Pa.s Oil vapor pressure 22.5 kPa d кра 4.5x10²
If a liquid enters a pipe of diameter d with a velocity, v. what will irs velocity at the exit be if the diameter reduces to 0.5d?
A Crude oil of specific gravity 0.81 and kinematic viscosity of 4.28 stoke is flowing through a pipe of diameter 460 mm at the rate of 4900 liters/sec. find the velocity, Reynolds Number & head lost due to friction for a length of 45 m of the pipe. Take the co-efficient of friction as 0.0058. Also find the Power required (in kW) to maintain the flow.
Engine oil at 40 deg.C, density is 875 kg/m3 flow into a 25.4 mm horizontal pipe with a velocity of 3.3 fps and exits through a nozzle of 0.20 in diameter. If the pressure drop is 78 psi, what must be the exit velocity in m/s? Show the unit cancellation.
her of partic Fluid Flow /Liquid of density 1200 kg/m² throgh a pipe of 50mm inte intemal dimeter an orifice, lo mm in dimeter is fitted in the life and differential Pressure Shwn on amercury manometer is 0-1 m. assuming the leads the manometer are filled with the flowing fluid, calculate @ the mass flow fate of fluid flowing the approximate drop in pressure. caused by the orifice in KN/m² pe of 50 mm in d differential the flowing flu ifice in kN/m the density bartle wers c the coefficient of discharge ugybe taken as 0-61 and the density of mercury is 13,550 kg/m³
1. A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm, and stroke L-5 mm. The fluid density is p = 800 kg/m³ and the viscosity is μ = 0.5 Pa-s. The pressure to drive the flow is p-6.25 Pa. a. How many non-dimensional groupings can be obtained? Derive them. b. If the flow transitions at Re = V(2R) =2300. Is the generated flow laminar or turbulent given Q=20 mL/s? c. Assume the pressure gradient is uniform on the cross-section and can be calculated using - The velocity profile in the cylinder is u(r) = [1-2²]. Sketch the velocity profile. Calculate the shear stress at the ax 2μ δχ cylinder wall and label the direction. d. Calculate the flow rate Q with the velocity profile in (c).. e. If the shear stress is uniform over the cross-section, i.e. T = C, what's the pressure gradient distribution and sketch it? L r L. R