C2. A conical tube is fixed vertically with itssmaller end upwards and it forms a part ofthe pipeline. The velocity at the smaller endis 4.9 m/s and at the larger end is 2.5 m/s.The length of the conical tube is 1.3 m andthe flow rate of the water is 127 liters/s. Thepressure at the smaller end is equivalent to ahead of 10.1 m of water.Considering the following two cases:(1) Neglecting friction, (without head loss)determine (i) the diameter at the smaller endin meter, (ii) the diameter at the larger end inmeter, and (ii) the pressure at the larger endof the tube in m of water.(2) If a head loss (with head loss)in thetube,h = 0.0153(V1-V2)2, where V1 is thevelocity at the smaller end and V2 is thevelocity at the larger end, determine (iv) thehead loss in m of water and (v) the pressureat the larger end of the tube in m of water.6) the diameter at the smaller end in meter(ii) the diameter at the larger end in meter(iii) the pressure head at the larger end of thetube in m of water(iv) the head loss in m of water(v) the pressure head at the larger end of thetube in m of water.

As per bartleby guidelines we are allowed to solve only 1st 3 subpart of a question. Please post…

C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The velocity at the smaller end is 4.9 m/s and at the larger end is 2.5 m/s. The length of the conical tube is 1.3 m and the flow rate of the water is 127 liters/s. The pressure at the smaller end is equivalent to a head of 10.1 m of water. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the diameter at the smaller end in meter, (ii) the diameter at the larger end in meter, and (i) the pressure at the larger end of the tube in m of water. (2) If a head loss (with head loss)in the tube, h = 0.0153(V1-V2)² , where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of water and (v) the pressure at the larger end of the tube in m of water. () the diameter at the smaller end in meter (ii) the diameter at the larger end in meter (ii) the pressure head at the larger end of the tube in m of water

C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The velocity at the smaller end is 4.9 m/s and at the larger end is 2.5 m/s. The length of the conical tube is 1.3 m and the flow rate of the water is 127 liters/s. The pressure at the smaller end is equivalent to a head of 10.1 m of water. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the diameter at the smaller end in meter, (ii) the diameter at the larger end in meter, and (i) the pressure at the larger end of the tube in m of water. (2) If a head loss (with head loss)in the tube, h = 0.0153(V1-V2)² , where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of water and (v) the pressure at the larger end of the tube in m of water. () the diameter at the smaller end in meter (ii) the diameter at the larger end in meter (ii) the pressure head at the larger end of the tube in m of water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The diameter at the smaller end is 245 mm and at the larger end is 467 mm. The length of the conical tube is 1.8 m and the flow rate of the oil is 128 liters/s. The pressure at the smaller end is equivalent to a head of 9.7 m of oil. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the velocity at the smaller end in m/s, (ii) the velocity at the larger end in m/s, and (iii) the pressure at the larger end of the tube. (2) If a head loss (with head loss) in the tube is hL= 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of oil and (v) the pressure at the larger end of the tube.
Two pipes, one of internal diameter (I.D.) 0.5 m and the other of I.D. 1 m, are connected as shown in Fig. 3 to a pipe of I.D. 1.2 m. Oil with a density of 880 kg/m3 flows through the pipe system at a total flowrate of 0.5 m3/s. If the liquid velocity in each of the two smaller-diameter pipes is the same, calculate this velocity, the corresponding volumetric and mass flowrates in the two pipes, and also the velocity in the large outlet pipe.
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
6.5 BELLOWS 6100mm The horizontal elbow is joined by bellows to the rest of the piping system and it transports water. Determine the X and Y components of the force needed to keep the elbov in posi- tion. The pressure at A and B is 200 kPa, the flow rate is 30 L/s and the pipe diameter is 100 mm. 6.6 Water flows at a rate of 0,055 m³/s through a piping system and then issues from the pipe of 50 mm diameter into the atmosphere. Ø150mm Ø50mm Ignore losses in the pipe and determine the force required at the flange to keep the nozzle in position. (Hint: first determine the pressure at A with Bernoulli's equation.)
Continuity equation: Calculate the inside diameter of the pipes at the inlet and outleta hydraulic pump whose volume flow is 40 l/min, knowing that the oil enters the pump at a speed of 1.2 m/sec andexits at a maximum speed of 3.5 m/sec. Answer: D1 = 26.6 mm and D2 = 15.6 mm
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The sucLon pipe is 350mm in diameter and 12m in length and the delivery pipe is 550mm in diameter and 40m in length. Calculate:(a) The maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (b) the energy to be supplied by the pump per unit mass of water transferred (c) The input power required by the pump, which is 60 % efficient
Consider a pipe on a horizontal plane: based on Bernoulli's equation A. none of the above B. the inlet velocity will be less than the outlet velocity C. the inlet velocity will be greater than the outlet velocity D. the elevation of the inlet will be greater than that of the outlet
Air velocity in a duct is measured as 38.2 m/s by a pitot tube. Density of flowing air 1.3 kg/m3. If the pressure difference recorded by the pitot static tube is 0.1 m of water, calculate the coefficient of velocity of the pitot static tube. A Figure or Free Body Diagram will be much appreciated. Thank you
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 10 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer b. Loss of Energy along the straight pipe = Answer J / kg. c. Losing Energy at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement of the pump ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
find the air flow through circular duct if the diameter(350mm) and velocity(6m/s) 0.048 m3/s O 0.37 m3/s O 0.81 m3/s O 0.11 m3/s O 0.57 m3/s O
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp