Blood flow from the left ventricle into the aorta can be modcled as a reducing nozzle. Model both the left ventricle and the aorta as a horizontal tube with diameter of 3.1 and 27 cm, respectively. The pressure in the left ventricle is 130 mmHg and the pressure in the aorta is 123 mmHg. Calculate the flow rate of the blood. ( Poiood = 1060 kgm-3)

Blood flow from the left ventricle into the aorta can be modcled as a reducing nozzle. Model both the left ventricle and the aorta as a horizontal tube with diameter of 3.1 and 27 cm, respectively. The pressure in the left ventricle is 130 mmHg and the pressure in the aorta is 123 mmHg. Calculate the flow rate of the blood. ( Poiood = 1060 kgm-3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the compression ratio is 17:1, the piston displacement volume for 10 cm³ piston clearance volume is. Ans. 160 cm³
A pump has a 100 mm diameter suction pipe and a 75 mm discharge pipe The capacity is 15 L/s of water A water- mercury manometer is installed in the inlet which reflects a vacuum pressure of 198mm of Hg The mercury level on the suction side is 100 mm below the pipe centerline. The pressure gauge 200 mm above the pump iniet recorded a pressure of 0.95 bar. The measured input power was 3.2 kW Find the efficiency of the pump Select the correct response(s) 75.12 % 60 42 % 59 01 % 80.43 %
her of partic Fluid Flow /Liquid of density 1200 kg/m² throgh a pipe of 50mm inte intemal dimeter an orifice, lo mm in dimeter is fitted in the life and differential Pressure Shwn on amercury manometer is 0-1 m. assuming the leads the manometer are filled with the flowing fluid, calculate @ the mass flow fate of fluid flowing the approximate drop in pressure. caused by the orifice in KN/m² pe of 50 mm in d differential the flowing flu ifice in kN/m the density bartle wers c the coefficient of discharge ugybe taken as 0-61 and the density of mercury is 13,550 kg/m³
The pressure of a reactor vessel can be adjusted bychanging either the inlet or outlet gaseous flow rate. Theoutlet flow is kept fixed as long as the tank pressure remainsbetween 100 and 120 psi, and pressure changes are treatedby manipulating the inlet flow control valve. However, if thepressure goes higher than these limits, the exit gas flow isthen changed. Finally, if the pressure exceeds 200 psi, a ventvalve on the vessel is opened and transfers the gas to a storagevessel. Design a control scheme that meets the performanceobjectives. Draw a process instrumentation diagram for theresulting control system
A pitot-static probe is used to determine the flow velocity of air at 20°C by using water manometer as shown in Figure 5. If the vertical difference of both arms in the manometer is 6 cm. Find, i. pitot formula to obtain the flow velocity ii. the pressure difference inside the system, and iii. air velocity inside the system. Air Pitot 6 cm tube Manometer Figure 5
pls ans asap Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the diameter of the pipe, in millimeter (mm), that was used is
1. A pressure gauge attached to a pipe is reading 1.34 m of Hg at a place where the atmospheric pressure is 10.33 m of water. The approximate absolute pressure at the mountain isa. 930 kPab. 181 kPac. 280 kPad. 100 kPa 2. The flow is said to be unsteady and non-uniform when,a. The flow velocity is not changing with time but changing with spaceb. The flow velocity is changing with both time and spacec. The flow velocity is changing with time but not changing with spaced. The flow velocity is not changing with both time and space 3. The below figure shows a pipe with a circular cross section of diameter D mm on the left end and a square cross section with side D mm on the right end. Mercury enters the left end with a velocity 1 cm/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe).a. Cannot be find since length is not givenb. Cannot be find since diameter is not givenc. 7.85 mm/sd. 12.73 mm/s 4. 1 kg water is flowing through an inclined pipe at…
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
(Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to measure the flow of water. The pressure at inlet is 20 N/cm2 and the vacuum pressure at the throat is 27 cm of mercury. Find the rate of flow. The value of cd may be taken as 0.9
The longest pipe run for a hot water system is 100 m. If the pressure rise through the pump is 35 kPa, then the pressure drop per one meter in system is إختر أحد الخيارات: Pa/m 233.3 .a O Pa/m 400 .bO Pa/m 250 .c O Pa/m 375 .d O
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp