Blocks A and B in (Figure 1) have a mass of 9.0 kg and 12 kg, respectively. Using the coefficients of static friction indicated, determine the largest vertical force P which can be applied to the cord without causing motion. 300 mm MD = 0.1 D B 400 mm MB=0.4 A MA=0.3 Mc=0.4 C

Blocks A and B in (Figure 1) have a mass of 9.0 kg and 12 kg, respectively. Using the coefficients of static friction indicated, determine the largest vertical force P which can be applied to the cord without causing motion. 300 mm MD = 0.1 D B 400 mm MB=0.4 A MA=0.3 Mc=0.4 C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.90RP: The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The...

See similar textbooks

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Blocks A and B in (Figure 1) have a mass of 9.0 kg and 12 kg,
respectively. Using the coefficients of static friction indicated,
determine the largest vertical force P which can be applied to the
cord without causing motion.
300 mm
MD = 0.1
D
B
400 mm
MB-0.4
A
PA=0.3
Mc=0.4
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given and FBD

VIEW

Step 2: The largest vertcal force P

VIEW

Step 3: Check

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A horizontal force of P = 100 N is just sufficient to hold the crate from sliding down the plane, and a horizontal force of P = 320N is required to just push the crate up the plane. 30° Part A Determine the coefficient of static friction between the plane and the crate. ANSWER: Us %3D Part B Find the mass of the crate. Express your answer with the appropriate units. ANSWER: m =
6. The crate in Figure 3.7 has a mass 350 kg and is subjected to a towing force P acting at an angle 01 = 20° with the horizontal. If the coefficient of static friction is 0.5, determine the magnitude of P to just start the crate moving down the plane. 02 = 10° Figure 3.7 P=986.61N
The crate has a weight of 490 lb and a center of gravity at G rests on the floor for which the coefficient of static friction is equal to 0.4. If the force P = 300 lb is applied as shown in the figure below. The force of friction developed between the crate and the ground is. -2 ft 2 ft- 3 4 2 ft 4 ft 3 ft A Figure 1
The crate has a weight of 490 lb and a center of gravity at G rests on the floor for which the coefficient of static friction is equal to 0.35. If the force P = 300 lb is applied as shown in the figure below. The static friction force developed between the crate and the ground is. -2 ft. 2 ft -2 ft- 2 ft 4 ft 3 ft A Figure 1 Select one: O a. 234.5-Ib O b. 300-lb O c. 240-lb O d. 610 lb 3.
The 500KN block shown is in contact with a 45°incline. The w coefficient of friction is 0.25. Determine the horizontal force P necessary to 1.Just start the block up the 45° incline 2.Just to prevent the motion down the incline. 3.lf P=400KN, what is the amount and direction of friction force?