BC:3.1 For the discrete time function f[n] (0.6)-¹ sin (n +90°) u[n+3] = a.) Sketch (by hand) the waveform for f[n] vs n. Label the value of the signal for the first 5 nonzero samples. b.) Sketch the waveform, x[n] = 10f[n] (u[n+ 5] - u[n - 4]) vs n. Label the values of x[n] for samples where -6 ≤ n ≤ 5. c.) Sketch the waveform for g[n] = f[n+ 1] vs n. Label the value of the signal, g[n], for the first 5 nonzero samples.

BC:3.1 For the discrete time function f[n] (0.6)-¹ sin (n +90°) u[n+3] = a.) Sketch (by hand) the waveform for f[n] vs n. Label the value of the signal for the first 5 nonzero samples. b.) Sketch the waveform, x[n] = 10f[n] (u[n+ 5] - u[n - 4]) vs n. Label the values of x[n] for samples where -6 ≤ n ≤ 5. c.) Sketch the waveform for g[n] = f[n+ 1] vs n. Label the value of the signal, g[n], for the first 5 nonzero samples.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ument-460F8C6BE9D6- x 5-1.pdf CD Page view A Read aloud 1: Theory 1.1 Describe briefly a sinusoidal signal and ALL its properties. Give example with figures. ongingoring which is si +.
1) what is the fundamental frequency (in units of Hz) of the given signal is 2)The period of the given signal is 3)The harmonic frequencies (in unit Hz) of this signals are
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
3) Determine the fundamental period of the signal x[n] = 1 + ej4mn1 – ej2mnl5. %3D
II. Design the following. N. 1) Design a clipper circuit of clipping the positive cycle of an AC signal of 3V at 2V. Draw the circuit and waveform. Show the complete solution for the output.
Q6. Figure Q6 shows a modulated waveform v(t) in microvolts as a function of time t in nanoseconds. 25 50 75 100 125 150 175 200 225 250 50 40 40 30 30 20 20 10 10 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 250 25 50 75 100 125 150 175 200 225 time/ns Figure Q6: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) The modulating wave in this example is substituted with a square wave of 50% duty cycle and of fundamental frequency 1.0 MHz. Sketch the absolute value of the spec- trum of the modulated waveform indicating the frequencies and relative magnitudes of the sideband components. (g) Demodulation of this type of signal is usually accomplished…
In a series connected RL circuit, if the circuit is fed with a square signal, the waveform below can be read over the resistor. R 150ohm 86.7uH Vtt 10V For F = 100kHz and a square signal input: A.) Calculate the half-life T of the RL circuit = 0.693 *) = In2 * .(T1/2
10 (Even Numbers will solve). Defined as is (t) = 3--3u (t-1) a) Draw the graph of is (t). b) Determine the general expression for the output voltage vo (t). c) Draw the graph of vo (t).
This subject is Signals, Spectra and Signal Processing. Choose one only below and explain its concept. I need this asap. Thank you so much.
Use multi-vibration circuits and create a signal generator that produces a square, triangular, and sinusoidal waveform with a frequency of 1kHz. Show work for theoretical layout. Also, use a switch for each waveform.
2. The signal x(t) = sin(2022nt) is sampled at 455 Hz. Deternmine the equivalent signal and sampled signal expression.
9. PLOT. Plot the sine wave at frequency fm and the sampling signal at frequency fs1. Write a MATLAB program to take input both fm and fs1 and plot the curves mentioned above.,.