Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is hollow with a wall thickness of 2 mm and section BC is solid. Knowing that P is 26 kN, applied to both sides of the bar at B and Q is 5 kN, applied to the bar at C as shown. What is the total %3D change in length of bar ABC? Express your answer in mm, to the nearest 0.01 mm, taking elongation as positive and contraction as negative. A B C 400 mm - 600 mm-

Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is hollow with a wall thickness of 2 mm and section BC is solid. Knowing that P is 26 kN, applied to both sides of the bar at B and Q is 5 kN, applied to the bar at C as shown. What is the total %3D change in length of bar ABC? Express your answer in mm, to the nearest 0.01 mm, taking elongation as positive and contraction as negative. A B C 400 mm - 600 mm-

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Similar questions

X Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.42 in.? and an elastic modulus of 2180 ksi. Bar (2) has a cross-sectional area of 1.139 in.? and an elastic modulus of 4150 ksi. Assume L;-23 in., L2-41 in., Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Determine the horizontal deflection of end Crelative to end A. R (1) (2) P L1 L2 Answer: UCIA - i 0.0725 in.
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. Find the largest value of P (kN) that will not exceed the maximum stresses are: 140 MPa in the steel, 120 MPa in the brass and 80 MPa in the aluminum. [Round off your final answer to 2 decimal places] Steel Brass A = 480 mm A = 650 mm? Aluminum A = 320 mm? 3P 4P 2P 1.0 m 2.0 m 1.5 m
Given : Steel: A = 600mm2 ; E = 200 GPa Bronze : A = 900mm2 ; E = 83 GPa Show the complete solution and FBD
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Bronze: A 1200 mm E83 GPa Lw2.0m What is the value of P Steel: A 900 mm E 200 GPa L=1.5m
REINFORCEB=(335mm)H=(435mm)
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
3. A steel bolt through a 25-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 79 degrees Fahrenheit. The cross-sectional area of the bolt is 0.08 sq. inch and the cross-sectional area of the tube of 0.25 sq. inch. For steel: E = 30 x 10^6 psi, coefficient of thermal expansion = 6.5 x 10^-6 per degree Fahrenheit. For aluminum: E = 10 x 10^6 psi, coefficient of thermal expansion = 13.0 x 10^-6 per degree Fahrenheit. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places. ) * Your answer This is a required question Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) * Your answer This is a required question Find the stress (in psi) induced in the steel bolt by the temperature change. * Your answer
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
We would like to increase the yield strength of the bar through cold work. (a) Using the Copper curve, how much cold work is needed to get a yield strength of 300MPa Yield strength (MPa) 800 700 600 500 400 300 200 100 0 10 20 1040 Steel Brass 30 40 50 Percent cold work Copper 60 70 (b) Based on the percent cold work you calculated, what should the final cross-sectional area of the bar be?
1. Find the Normal Stresses experienced by the Steel, Aluminum, and Bronze section of the given body. The value of P is 3000 pounds and the cross-sectional area of the rod is equal to 0.5 squared inches. Steel Aluminum Bronze 4P = 12k P 3k