(b). You are given a photodiode D1, a capacitor C₁, a resistor R₁ and an operational amplifier which operates at a supply voltage of 5 V. Draw a clearly labelled circuit diagram showing how you can construct a TIA from the given components for detecting and converting weak optical signals into electrical signals. (c). What component value should it be for one of the electronic components or devices in Q2(b) required for getting the specified signal gain?

(b). You are given a photodiode D1, a capacitor C₁, a resistor R₁ and an operational amplifier which operates at a supply voltage of 5 V. Draw a clearly labelled circuit diagram showing how you can construct a TIA from the given components for detecting and converting weak optical signals into electrical signals. (c). What component value should it be for one of the electronic components or devices in Q2(b) required for getting the specified signal gain?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

help me please on this question
a ): The depletion region is a layer of positive and negative charge in the semiconductormaterial Briefly explain how the depletion region formed in the semiconductormaterial after the PN junction is created.b): An audio signal amplifier is used to reproduce input audio signals at sound-producoutput elements, with desired volume and power levels. What is the function of volumecontrol and power amplifier in an audio signal amplifier ?
I need the solution quickly with in 15 minutes
2 V 1ΚΩ VOUT Find the following: a. Vout b. Small signal model of the diode under these conditions (Do NOT consider capacitance across the diode junction and the resistance of the semiconductor material outside the diode junction) c. Approx. peak-to-peak value of the AC component of Vout if a 1 mV RMS sinusoidal signal is added to the 2 V DC source. Given that: reverse saturation current is 1.5 x 10-14 A, ideality factor is 1.1, and the circuit is operating at 27°C.
3. Circuit in Figure B.3 is designed to provide a DC voltage of 20 V to a load resistance, RL. The input voltage, Vi, varies from 30 in Table B.1, select one zener diode that is suitable for the above circuit operation. Show relevant calculation to justify your selection. UTM OV to 50 V. Based on the parameters given UTM Rs 0.75 k2 UTM & UTM UTM & UTM UTM UTM V, SUTM & UTM TM 2.5 k2 UTM UTM UTM Table B.1 Zener Diode Vz (V) UTM &UTM & UTM PDMAX (W) ZA UTM UTM ZB 0.5 5 ZC 1 15 ZD 0.5 15 JUTM UTM 5 UTM ZE 20 UTM UTM ZF 0.5 1 UTM UTM20 & UTM & UTM & UTM UTM UTM TM UTM TTM UTM
3. Circuit in Figure B.3 is designed to provide a DC voltage of 20 V to a load resistance, RL. UTM Show relevant calculation to justify your selection. The input voltage, Vi, varies from 30 V to 50 V. Based on the parameters given in Table B.1, select one zener diode that is suitable for the above circuit operation. 5 UTM Rs 0.75 k2 UTM & UTM UTM & UTM UTM 3 UTM TM Vi 2.5 ko 5 UTM 5 UTM VL UTM UTM UTM UTM UTM Pigure B 3 Table B.1 Vz (V) UTM UTM 3 UTM PDMAX (W) Zener Diode ZA UTM & UTM ZB 0.5 5 1 15 ZD 0.5 15 UTM UTM 5 UTM ZE 20 UTM UTM ZF 0.5 1 5 UTM UTM 20 5 UTM & UTM & UTM
Kindly answer the following question (as soon as possible) #35
TEST Read the question carefully. Write the letter for each correct answer in the blank space provided. A 1. Maximum power is delivered from a source of power to a load when the a. load current is equal to the power source current b. impedance of the load is equal to the output impedance of the power source c. output impedance of the power source is high compared to the impedance of the load d. output impedance of the power source is low compared to the impedance of the load 2. The emitter follower is a (an) a. impedance matching device b. high gain voltage amplifier c. phase inverter d. combination power and voltage amplifier 3. The emitter follower uses a. no collector resistor b. a forward bias collector-base junction c. negative feedback (degeneration) d. an NPN transistor only 4. The emitter follower has output resistance. a. high, high b. low, low c. low, high d. high, low input resistance and 5. The current gain of an emitter follower is a. less than 1 b. equal to 1 c. greater…
Please solve it.
Refer to the circuit. Consider ideal model (V_D=0) of diode circuits. Given V_i =100 Volts peak-to-peak sinusoidal input (+50, -50 Voltage peaks). Determine the peak output voltage during the diode non-conduction cycle.
Q.7 Light-emitting diode (LED) is simply a diode that is designed to emit light. Voltage drop for LED is 0.8V. What happens to the LED when it is connected to the voltage source as in Figure A1? Why? (Describe in terms of majority carrier movement). LED 5V 1kQ Figure Al
State whether the followings statements are true or false.3.1.1 The process of adding impurities to an intrinsic (pure) semiconductor toincrease and control conductivity is called forward bias.3.1.2 A varactor diode acts as a variable capacitor under reverse biasedcondition.3.1.3 Hole is the presence of electron in the valence band of an atom. 3.1.4 The output voltage of the bridge rectifier is twice the total secondaryvoltage.