(b) What is the difference between a balanced load and an unbalanced load? Explain the power measurement methods in a star-connected circuit: 'one-wattmeter method,' 'two-wattmeter method' and 'three-wattmeter method' with suitable diagram, and explain why the three- wattmeter method is not applicable for a three-phase balanced load?

(b) What is the difference between a balanced load and an unbalanced load? Explain the power measurement methods in a star-connected circuit: 'one-wattmeter method,' 'two-wattmeter method' and 'three-wattmeter method' with suitable diagram, and explain why the three- wattmeter method is not applicable for a three-phase balanced load?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.25P: Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows:...

See similar textbooks

Similar questions

The voltages of a two-phase system are how many degrees out of phase with each other?
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
How does a three-phase power system differ from a single-phase system, and what are the advantages of using three-phase power?
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
2-What is the relationship between phase and line quantities in balanced star and delta connections in three phase circuit balanced ? Why?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
What is the significance of a three-phase power system, and how does it differ from a single-phase power system?
(Balanced 3-Phase Circuit) 1-What is the relationship between phase and line quantities in balanced star anddelta connections? Why?2-What was the effect of neutral wire removal?3-Draw the phasor diagram of voltages and currents for both star anddelta connections.
a. If two wattmeters are used to measure total power in a three-phase three-wire systemdoes each meter measure single-phase power? Explain.b. What is the significance of a negative indication on a wattmeter?c. Would only one wattmeter be needed to measure the total three-phase power on abalanced three-phase four-wire system? Explain.
1. How do you measure three phase line currents by using two current transformers? Draw the connection scheme.
One advantages of load balancing is that each phase conductor carries the ? current value
What is the difference between a balanced load and an unbalanced load? Explain the power measurement methods in a star-connected circuit :one wattmeter method; two wattmeter method 'and three -wattmeter method 'with suitable diagram, and explain why the three-wattmeter method is not applicable for a three phase balanced load?