(b) For the balanced three phase system shown below, it is determined that 200W is dissipated is lost in each wire. If the phase voltage is 380V, and the load draws 10KW at 0.85 lagging power factor, determine the wire resistance Rw?

(b) For the balanced three phase system shown below, it is determined that 200W is dissipated is lost in each wire. If the phase voltage is 380V, and the load draws 10KW at 0.85 lagging power factor, determine the wire resistance Rw?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Related questions

Q: Non-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and…

A: according to the question, we have to find, I. What should be the total current in each line and the…

Q: For an ac three-phase four wire system, having a voltage of 415 V, with load of 120 kW and…

A: Given three phase four wire systemHaving voltage V=415 vLoad P=120 kw Resistance R=0.05 ΩPower…

Q: .2 For each set of voltages, state whether or not the voltages form a balanced three-phase set. If…

A: The solution is as follows.

Q: Two wattmeter's are connected to measur the input power of a balanced three phase load by two…

A: Watt-merter reading W1 = 8800w W2 = 3500 W

Q: 4. A balanced Y-connected 400V voltage source is where Z, = 20-j40 and Z2 = 3+ j45 Ohms a connected.…

A: In this question we will find source current in per unit....

Q: If the current in the neutral wire of a typical 120/240-V distribution system equals zero, a.…

A: If the current in the neutral wire of a typical distribution system is zero, it indicates the load…

Q: In the balanced three-phase parallel circuit below, complete the tables using the provided values.…

Q: The c-phase voltage of a balanced three-phase Y-connected system is 450 −25° V. If the phase…

Q: Which of the following statement is wrong for 3 phase 4 wire ac distribution systems? O Under…

A: Distribution system for 3phase 4 wire system

Q: Compute for the power of a three phase, three wire, 50HZ, balanced and negative sequence power…

A: In the question, Find the three phase power in the following in the following information, This is…

Q: Obtain the readings of wattmeter 1 and wattmeter 2 in a three-phase three-wire system having…

Q: The power flowing in a three-phase, three-wire balanced load system is measured by the two-wattmeter…

A: Given Data, The reading on wattmeter A =5kW The reading on wattmeter B = -1kW

Q: A Factory is supplied froma 3-phase, 4-wire, 400 V, simmetrical system. The resistance of each line…

Q: A balanced delta-connected load with impedance (25.98 + j15) ohms per phase is connected to a…

A: Given data, Zper phase=25.95+j15 Ω Zc=0.4+j0.3 Ω Line voltage V=250 V

Q: At what power factor will one of the wattmeter reading be zero in a three-phase system???

A: W1=VLIL cos(30-∅)W2=VLIL cos(30+∅)

Q: In a 3-phase, 4-wire system, two phases have currents of 10 A and 6 A in lagging power factors of…

Q: The minimum number of wattmeter(s) required for measuring power of 3-phase balanced load is

A: Step1 In this question, we have to find out minimum number of wattmeters required for measuring…

Q: 6. The power flowing in a 3-0, 3-wire, balanced-load system is measured by the two wattmeter method.…

Q: In a balanced 3 phase 415 V connection, the line current is 135 A. When power is measured by two…

A: Power factor: The real power measured in kilowatts divided by the apparent power measured in…

Q: In the circuit of figure shown in the next slide, three impedances are 12 – j10 ohms, 10 + j20 ohms,…

A: In this question, We need to calculate the a. Current in each impedance b. Neutral current In c.…

Q: In a balanced 3-phase 400-V circuit, the line current is 115. A. When power is measured by two…

A: The data given in the question are: VL=400V, I=115A, P1=40kW, P2=0 The power factor angle is given…

Q: A balanced Y-connected voltage source with E = 277/0° volts is applied to a balanced-Y load in…

Q: 8. A 415-V, 3-phase, 4-wire system supplies power to three non-inductive loads. The loads are 25 kW…

A: Question-4 is not in the question. As per the policy we can solve only one question, please…

Q: In the balanced three-phase parallel circuit below, complete the tables using the provided values.…

A: Given W1=350 W V2=230 V A2=0.8 A A4 =0.51798 A PFload1 =0.6 lag θZT=18.19490

Q: A three-phase, four-wire system operating with a 208-V line voltage is shown in the figure. The…

Q: 6. In a 3 phase, 4 wire system, there is a balanced 3 phase motor load taking 200 kW at a power…

A: In this question we have given 3 phase 4 wire system in which balanced motor and lamps load is…

Q: Non-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and…

A: Line voltage =400V Phase voltage=4003=230.95VPR=Vph2R ∴ Resistance in R phase=Vph2PR=4003210k…

Q: 6. The power flowing in a 3-o, 3-wire, balanced-load system is measured by the two wattmete method.…

Q: A three phase 60 Hz transmission line delivers 750 KW at 95% leading power factor and at delta…

Q: For an ac three-phase four wire system, having a voltage of 415 V, with load of 120 kW and…

A: As it is not given about the state of system, we will assume it to be balanced and in balanced…

Q: Two wattmeter’s are connected to measure the input power of a balanced three phase load by two…

A: As one of wattmeter is connected with reverse switch so it will reading negative power.

Q: A three phase transmission line to line capacitive reactance value is 12 ohms. If the charging…

Q: Obtain the readings of wattmeter 1 and wattmeter 2 in a three-phase, three-wire system having…

Q: The power flowing in a 3-phase, 3 wire, balanced load system is measured by the two wattmeter the…

A: Given, WA = 5000 WWB = -1000 W Therefore, WA + WB = 4000 WWA - WB = 6000 W Where, WA - Wattmeter A…

Q: In the circuit of figure shown in the next slide, three impedances are 12 – j10 ohms, 10 + j20 ohms,…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: One conductor of a three-phase line is open. The current flowing to the A-connected load through…

A: Let Ia , Ib and Ic are the line currents flowing through the load and I0 is the zero-sequence…

Q: balanced 3-phase load draws 120 amperes line current at 230 volts line to line, 0.848 pf lagging…

A: We need to find out power .

Q: In a balanced three-phase system, Vbn = 277≮30º. If you could measure the magnitude and angle of…

A: Given, a balanced three phase system. Vbn = 277 < 30° To find the magnitude and angle of line Vac…

Q: na two-phase circuit, find the unbalance factor of the load voltage when one wire is disconnected.…

A: To find unbalanced factor in two phase circuit. Explanation below

Q: Q. 2a) The impedance Z, and Z2 are connected in parallel across 200 V, 50 HZ single phase ac supply.…

A: Given two impedances are in parallel. Current through Z1 is 2∠-36.86°A. Current through Z2 is I∠θ°A.…

Q: Poor power factor causes greater voltage drop because the line voltage drop depends on the a. line…

A: power in circuit is p = voltage* current * power factor. voltage drop is current * line resistance

Q: The three-phase source line-to-neutral voltages are given by Ean= 10/0 Em Een= 10/-240 volts.…

A: The three-phase source line to neutral voltage is given below; Ean=10∠0. VEbn=10∠+240. VEcn=10∠-240.…

Q: le, 230 volt (line to line) 60 Hz. Y con 5 2, Ra - 0.25 2, X1 = 0.75 2, on and windage loss is 150…

A: Since you posted a question with multiple sub-parts. We will solve the first three sub-parts for…

Q: In a balanced 3 phase 400 V connection, the line current is 115.5 A. When power is measured by two…

A: Given that P1=40 WP2=0WIL=115.5 AVL=400V (a) Although when power is measured by two wattmeter…

Q: For abe phase sequence, calculate the line currents for a balanced three-phase wye-wye system as…

A: Given a balanced three phase wye-wye system,

Q: What would be the phase-to-neutral voltage from a 3-phase, wye-connected system if the line-to-line…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

(b) For the balanced three phase system shown below, it is determined that 200W is dissipated is
lost in each wire. If the phase voltage is 380V, and the load draws 10KW at 0.85 lagging power
factor, determine the wire resistance Rw?
1
R
V.
12+
Zp
R
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a. Using Ohm’s Law, compute the voltage and current for eachcomponent. Use the formula Z = Vt / It. b. Compute and record the magnitude and phase angle of the impedanceusing the equation Z= R + RL + jXL – JXC. Use 3uF for the value of C,1.006H for the value of L and for the resistance is computed based onthe specification of the lamp. c. Compute and record for the total power using the formula: Pcomputed = Scosθ d. Compute and record the reactive power and apparent power using theformula Scomputed = V2/ZQcomputed = √S2 − P2 e. Compute for the reactive power (measure) and apparent power(measured) using the formula.Q = PtanθS = P/ cos θ f. Compute the percent difference between the measure and the computedvalue of the impedance.
For the circuit in the figure calculate: Line and phase currents Line voltages at the load The neutral current Draw the phasor diagram for currents and voltages
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
ChatGPT 3.5 You A balanced load is connected in star across a 3 phase 415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inductance 0.5 henry in parallel with a pure resistance of 28 ohms and a pure capacitor of 60 microfarads capacitance ib each branch Calculate I. The line currents Ii. The overall power factor. iii. The power delivered from the supply. iv. The power dissipated in the resistors and coils. v. The current in the neutral supported by a reason why its value is that deduced ?
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
Compute the admittance in millisiemens if R = 19 ohmsXL = 10 ohmsXC = 21 ohms State the phase relation for current & voltage in the circuit. Answer this way: I ( leads / lags / is in phase with ) E by angle° Example Answer: I leads E by 1.2345°
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
The values of the elements for the given circuit are given below.What is the maximum average power that can be transferred to the ZL load? R1 = 400 Ohm L = 500j Ohm R2 = 100 Ohmanswer choices are in the picture
50. A series resistance-capacitance (R-C) circuit is connected to 230-volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: a. Ohmic value of the resistor b. Capacitive reactance E. capacitance in microfarad
current - 1=?, and the power factor - cosp =?. 4. An out of balance three phase star connected load has the following complex currents: I₁ = lejº,A, I₂ =le¯6⁰,A and I₁=1e¹j6⁰, A. This load is supplied by a four wire power line from a balance voltage source. Find the r.m.s. value of the neutral current Io =? Wait to th
If ZTh = 3.33∠33.7 and VTh = 16.5∠33.7o V maximum power for the load will be a. 6.25 W b. 24.6 W c. 18.38 W d. 2.8 W