B- Choice the correct answer 1. The energy storage capacity of a cell is determined by the: (a)Terminal voltage (b) Electrolyte specific gravity (c) Amount of material available for chemical reaction (d) Terminal earthing. 2. The reason for having an even number of positive plates in a lead-acid Battery is because: (a) positive plates distort when chemical reactions take place on both sides (b) positive plates distort when chemical reactions take place on one side

B- Choice the correct answer 1. The energy storage capacity of a cell is determined by the: (a)Terminal voltage (b) Electrolyte specific gravity (c) Amount of material available for chemical reaction (d) Terminal earthing. 2. The reason for having an even number of positive plates in a lead-acid Battery is because: (a) positive plates distort when chemical reactions take place on both sides (b) positive plates distort when chemical reactions take place on one side

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter2: Basic Electricity

Section: Chapter Questions

Problem 21RQ: Describe briefly the method a dry cell battery uses to produce voltage.

See similar textbooks

Similar questions

Describe briefly the method a dry cell battery uses to produce voltage.
For solar cell the Open Circuit Voltage (Voc) occurs when O a. voltage is minimium f O b. voltage is zero ion O C. current is maximium O d. current is zero page
For number 12 question Final problem, you will need a test charge to move from one point to another point. Please consider the value of the test charge 15 mC 12. Determine the work needed to move a 13.3 mC charge from 1.2 mm to 0.41 cm.
Question 7 One of the following elements can be used to make P-type semiconductor Phosphor(P) Arsenic(As) Antimony(Sb) Aluminum (Al) A Moving to another question will save this response.
Current can not flow through an insulator because they have O a. free electrons O b. no free protons O c. no free electrons O d. free neutrons
In order to identify the function of the parts of an electronic system, the Blank 1 diagram system representation is used. Blank 1 Add your answer A Si diode has a leakage current Is = 40 nA at room temperature (25°). The leakage current if the temperature increases to 43 °C is nA. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places. Add your answer Short answer. In testing a diode, if the red probe of an analog ohmmeter is tapped at the anode while the black probe is at the cathode, what is the ohmmeter reading if the diode is in good condition? Use the editor to format your answer
In an n-type semiconductor material, the net flow of charge will be the flow of Blank 1. Blank 1 Add your answer In semiconductors, if more impurities are added, their doping level is termed as Blank 1 doped semiconductors. Blank 1 Add your answer A device that converts one form of energy to another is called a/an Blank 1. Blank 1 Add your answer
In the figure below you see the sketches for the front and back of an electrical circuit board. The board is cut into a trapezoidal shape and is made of plastic. On the back of the board there is conductive paint shown here in green. On the front there are some resistors and capacitors, in addition to terminals for inserting the leads from a DC power supply. The legs of the resistors and capacitors go through the holes on the board and are soldered to the conducting paint on the back side. You also have a multi-meter which you can use as an ammeter or a voltmeter. 16 v 4700 16 10 8 O- 7 3. 6. 4 O+
Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The internal resistances are 0.004, 0.005, 0.003 and 0.0025 ohm. Calculate for parallel connections: (a) internal emf and resistance of the single equivalent cell (b) current for a terminal voltage of 1.95 volts, (c)current in each cell
Electrons flow from the positive battery terminal towards the negative terminal. A. True B. False
Which material is always conductive? Metal semiconductor Insulator
A series circuit is set up with an AA battery along with an mystery material and ammeter; however, there’s no current passing through. A.Insulator B.Conductor C.Semiconductor