At an axial load of 24 kN, a 40-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.7 mm while the bar width contracts 0.18 mm. The bar is 180 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= I Mi Mi GPa mm

At an axial load of 24 kN, a 40-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.7 mm while the bar width contracts 0.18 mm. The bar is 180 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= I Mi Mi GPa mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.4P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
At an axial load of 20 kN, a 35-mm-wide by 10-mm-thick polyimide polymer bar elongates 2.7 mm while the bar width contracts 0.15 mm. The bar is 240 mm long. At the 20-kN load, the stress in the polymer bar is less than its proportional limit.Determine(a) the modulus of elasticity.(b) Poisson’s ratio.(c) the change in the bar thickness.
At an axial load of 20 kN, a 45-mm-wide by 10-mm-thick polyimide polymer bar elongates 3.3 mm while the bar width contracts 0.21 mm. The bar is 240 mm long. At the 20-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= i i i GPa mm
At an axial load of 22 kN, a 45-mm-wide by 15-mm-thick polyimide polymer bar elongates 2.8 mm while the bar width contracts 0.25 mm. The bar is 190 mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness
At an axial load of 25 kN, a 50-mm-wide by 15-mm-thick polyimide polymer bar elongates 3.1 mm while the bar width contracts 0.26 mm. The bar is 220 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E- (b) v- (c) Audness GPa mm
At an axial load of 22 kN, a 15-mm-thick x 35-mm-wide polyimide polymer bar elongates 4.2 mm while the bar width contracts 0.25 mm. The bar is 215-mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine Poisson's ratio. O 0.366 O 0.336 EBA O 0.473 O 0.229 O 0.427
At an axial load of 22 kN, a 15-mm-thick x 45-mm-wide polyimide polymer bar elongates 3.9 mm while the bar width contracts 0.25 mm. The bar is 265-mm long. At the 22-kN load, the stress in the polymer bar is less than its proportional limit. Determine Poisson's ratio. O 0.237 O 0.483 O 0.434 O 0.377 O 0.352
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 620 mm. The cross-sectional dimensions of the beam are b = 37 mm, d1 = 80 mm, b2 = 22 mm, d2 = 22 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 12 MPa, and the allowable compressive bending stress is 11 MPa. Determine the largest moment M that can be applied as shown to the bearn. b, a M d2 d | 4 B b1 Answer: M = i N-m
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm. The cross-sectional dimensions of the beam are b1 = 37 mm, d1 = 117 mm, b2 = 22 mm, d2 = 22 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M | A В
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b₁ = 38 mm, d₁ = 82 mm, b₂ = 23 mm, d₂ = 23 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 14 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b₂ a M d₁ B L N-m | A Answer: M= d₂ b₁
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 560 mm. The cross-sectional dimensions of the beam are b1 = 32 mm, d1 = 118 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 14 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M d2 | A В b1 Answer: M = i N-m