Assume register R0, R1 and R2 contain the value of 0x00000100, 0xAABB1122 and 0x00000102. ARM Cortex-M3 processor executes the instructions STR R1, [R0] and LDRB R1, [R2] in sequence. What is the content of register R1 if the storing mode of data in memory using Little Endian Mode?

Assume register R0, R1 and R2 contain the value of 0x00000100, 0xAABB1122 and 0x00000102. ARM Cortex-M3 processor executes the instructions STR R1, [R0] and LDRB R1, [R2] in sequence. What is the content of register R1 if the storing mode of data in memory using Little Endian Mode?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Q: Q2. Write assembly language program to substrate two 8-bit numbers and store the result on memory…

A: considering the two 8 bit numbers are located in the locations 2000H and 2001H. and the result will…

Q: Write a ALP for 8086 to exchange the content of AL and AH registers without using XCHG instruction.

A: We can use BL register to swap the value of AL and AH registers , the code for the same is as…

Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is…

Q: Q11:design a two input logic circuit (A, B) to implement And, Or,Xor,Complement using Mux and logic…

A: As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Q: Explain the SUB instruction of 8086. Compare it with SBB instruction. Write a Assembly language…

A: 8086 microprocessor is 16 bit microprocessor and contains 20 address lines and 16 data lines. 16…

Q: Q12/Assume that the microprocessor can directly address 1M with a and 8 data pins, The maximum RAM…

A: To find - Total capacity

Q: The registers that are necessary in the operations of memory data write and read (which of the…

Q: a) Compare between the Logic families : Transistor-Transistor logic and CMOS logic

A: Comparison between Transistor-Transistor logic and CMOS logic is shown below

Q: 1. Draw the figure showing the types of registers in an 8086 microprocessor. Write the register…

A: There are a total of five registers in an 8086 microprocessor. They are General purpose registers…

Q: A question about 74LS04 IC (a Schmitt Trigger). The pictures show the 74LS04 logic, the connection…

A: According to the question, we need to find the voltage logic at pin 1 and point A and the current…

Q: Flag Register is a special purpose. Name two types of registers used in 8086 microprocessor.…

A: MOV AL, 50 → positive numberMOV BL,32→poistive number ADD AL,BL…

Q: Study and then differentiate between RAM and ROM memory units in a processor. Describe any possible…

A: Difference between RAM and ROM Key RAM ROM Definition RAM stands for Random Access Memory ROM…

Q: Explain the program memory structure of 8051 microcontroller.

A: We are authorized to answer one question at a time since you have not mentioned which one you are…

Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FOO2H, AX= 0105H, and the following memory content.what is the…

Q: question1:In a memory system, data is 16-bit wide. Break the information into bytes with their…

A: solution:1)Big-Endian method:-In Big Endian machine, first byte of binary representation of he…

Q: Q4: (A)-Create an 8086 Assembly language program that subtracts two 8-bit ASCII numbers, the first…

A: First we will initialize the data segments. then move the data from the address 200 and 400 to AL…

Q: 4) Design and draw these memory units with their control circuits. Explain operations. a) A single…

A: As per the rules we can answer only one question, please post the remaining questions as the…

Q: Continuing with a 32 Khz system clock/8000 Khz instruction clock, assuming a pre-scalar of 1:1 (i.e.…

A: According to the question, for continuing with a 32 kHz system clock/8000 kHz instruction clock,…

Q: Q/ -How many address lines are required for 4 kB memory addressing

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: b) The number of addressed words in a ROM is determined from some fact. 92 × 8 ROM architecture…

A: According to the question, The number of address words in a ROM is determined by some fact. 92 X 8…

Q: 1- Write an 8086 assembly language program to multiply the contents of the registers CL & BL by…

A: MOV A 00H move 00 in A register. Repeat : Add AL ,BL

Q: In a RAM chip of size 256M x 32, what are the number of data lines and address lines?

A: Buses have a address lines data lines and control lines. The data lines: Convey bits…

Q: For the circuits shown in figures 1 and 2:- What is the function of output? 2. Find the max. and…

Q: in Intel 8086 microprocessor, the memory address for the code segment 771F h and offset 3584 h is O…

A: memory address = code segment + offset 1. Given code segment = 771F and offset = 3584 H code…

Q: Refer to the following registers values and memory snippet to answer the following questions.…

A: The 8086 microprocessor is a 16 bit microprocessor with 16 data lines and 20 address lines. It is…

Q: draw and identify or explain Make na input circuit using a switch and an external pull-up resistor.…

A: Pull up resistor can be used in following two ways- When pin is to be used as an input pin, we use…

Q: 1. Design 8086’s memory system consisting of 64K bytes of ROM using 32KX8 chip. The memory is to…

A: according to our policy we can only solve one. as you mentioned any question so I'm solving 2.

Q: Q7. Discuss types of registers that should be implemented in any microprocessor

A: The registers implemented inside any microprocessor are all 16 bits. They are : General Purpose…

Q: Suppose we have two registers, Rl and R2, and between them we have a combinational logic circuit.…

A: Formula of maximum frequency; fc(max)=1Tmax Formula of Tmax; Tmax=tpcq+tpd+tsu+tccq+tcd+th…

Q: Which of the following is incorrect? Select one or more: In AVR, the data memory includes 32 general…

A: ANSWER:- OPTIONS- A,B,D

Q: What is the maximum memory size that can be connected to a processor with a lower order address bus…

A: What is the maximum memory size lower order address bus 24 lines higher order address bus of 4…

Q: For the ROM memory chip shown, find the capacity (including units): . organization: is this memory…

A: The ROM is a Non Volatile Memory.

Q: In the MIPS processor that is part of the PIC32 microcontroller, what is the length of each…

A: MIPS stands for Microprocessor without Interlocked Pipelined Stages. MIPS processor is a part of the…

Q: Write an assembly language program in 8086 microprocessor to find square root of a number

A: We are authorized to answer one question at a time. Since you have not mentioned which question you…

Q: B) Name the intemal registers of 8086. Table the combination of registers to form the physical…

A: Internal Registers of 8086 : Instruction Pointer Four Data Register Four Pointer & Index…

Q: Subject Name: Microprocessor and Assembly Language ( 8085) Question: - What is an Addressing…

Q: Assume that the contents of 8086 microprocessor registers are: DS= 3300H, CS=1033H, SS= 1614H, SP=…

A: The stack memory at 1E76A H is not covered by the segment. This is because the maximum value of the…

Q: Q1: Choose the correct answer for the following statements is a programmable logic device that has…

A: is a programmable logic device that has fixed AND array & Programmable OR array.

Q: Develop a 64-bit wide memory interface that Contains SRAM at locations (EEFE80000- EEFEFFFFF) H and…

Q: A memory chip from a digital camera has 25 bistable (ON-OFF) memory elements. What is the total…

A: Given: Find the total number of ON-OFF configuration

Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FOO2H, AX= 0105H, and the following memory content.what is the…

Q: a) Convert the following unsigned binary numbers to decimal. i) 101101112 ii) 010011012 iii)…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: There are different types of memories used in 8086 microprocessor one of them is called Stack. You…

A: As per our policy i have attempted first three sub-part only. (i) In stack memory the allocation…

Q: Identify the contents of the registers, the memory location (C055H), and the flags as the following…

A: The contents of flag registers are modified when arithmetic and logical instructions are executed.…

Q: Question: Assume a system comprises 16 GB physical memory with B KB page/frame sie and the…

A: Virtual memory is a volatile memory . it store the temporary data . virtual memory used both the…

Q: Briefly answer the following questions: a) List at least 5 SFRs in PIC18F87J11. b) Given an…

A: 1) SFRs in PIC18F87J11. The Special Function Registers (SFRs) are registers usedby the CPU and…

Q: 3) Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX-1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H,…

A: Dear student ,you have posted 2 question in a single request.We will answer first question only.If…

Q: 14.) Using rising edge JK-Flipflops and Digital Logic Gates, build a 4-Stage Shift Register. I…

A: By using rising edge JK-Flip flops and the Digital Logic Gates Building a 4-stage Shift Registor is…

Question

0xAABB11BB

0xAABB1111

0xAABB1122

0x0000BBAA

0x00001122

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
DIsassemble the following MIPS 32-bit hexadecimal instruction written as addr:instr 60005000 : 0c000020
(a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits, which shift register I should explain it with the help of circuit diagram and table. (b). Write comparison between Diode transistor logic and Transistor Transistor logic
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
P Flag question Explain the MUL instruction of 8086. Compare it with IMUL instruction. (1 +1 Marks) Write a Assembly language program for 8086 to find the cube of a number using MUL instruction. (5 Marks) (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) B I III
For a microprocessor similar to ATmega328p an 8 bit ADC uses a VREF = 3.3 V. When an analog read is executed the return value is 112. What Voltage is present on the input? Enter the value in the box provided in mV. Round to the nearest mV.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
1.Assume that one input of a two-input AND gate is connected to a square wave. If the other input is connected to a logic high, what will be present on the output? A. A constant logic high B. A square wave C. A square wave that mirrors the input square wave D. A constant logic low
8:37 4 A M Vo) Gt LTE1 You Just now i) Analyse and execute the following 8051 Instructions and specify the output and explain the contents of the registers with comments MOV A, #92H SWAP A In the absence of a SWAP instruction, how would you exchange the nibbles? Write an 8051 ALP to show the process ii) Analyse and execute the following 8051 Instructions and specify the output and explain the contents of the registers with comments. CLRC MOV A, #4FH SUBB A#6DH JNC NXT CPL A INC A NXT: MOV RI,A ADD A,RI
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0