As shown in Figure 2.3, the total height of the liquid in the canal in Part (a) is now increased to 3R. Determine the minimum force F applied at B to prevent the gate ABC from opening (i.e. turning anticlockwise about the hinge A). Neglect the weight of the gate and friction in the hinge. F- 2R Air с B Gate R Air Liquid Hinge Figure 2.3 Р 77. gv

As shown in Figure 2.3, the total height of the liquid in the canal in Part (a) is now increased to 3R. Determine the minimum force F applied at B to prevent the gate ABC from opening (i.e. turning anticlockwise about the hinge A). Neglect the weight of the gate and friction in the hinge. F- 2R Air с B Gate R Air Liquid Hinge Figure 2.3 Р 77. gv

Name: As shown in Figure 2.3, the total height of the liquid in the canal i
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: As shown in Figure 2.3, the total height of the liquid in the canal in Part(a) is now increased to 3R. Determine the minimum force F applied at B toprevent the gate ABC from opening (i.e. turning anticlockwise about thehinge A). Neglect the weight o

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.119P: Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
Find the force P required to hold the gate in the position as shown in the figure. The gate is 5 meters wide.
In the following figure, the horizontal surface onwhich this block slides is frictionless. If the two forcesacting on it each have magnitude F = 30.0 N andM = 10.0 kg , what is the magnitude of the resultingacceleration of the block?
The vessel shown below contains linseed oil at 77° F. One side of the vessel contains a spout which is sealed with a 12-inch diameter flat circular gate hinged along its top edge. The horizontal axis of the hinge is located 6 feet below the water's surface. Determine the minimum required torque (moment) on the hinge to hold the gate shut. Neglect the weight of the gate and friction in the hinge. 6 feet Hinge 12-inch dia. gate Linseed oil
The hydraulic jack is filled with oil (S-0.9). Neglecting the weight of the two pistons, what force F on the handle is required to support the block mass of m=222 kg for this design? 6 cm diameter 5 cm 30 cm 3 cm diameter
6- The rectangular gat has dimensions 6 m by 2 m. Neglect the weight of the gate. Determine (a) The magnitude and location of the resultant force Hinge exerted on the gate by the water Atmospheric pressure (b) The reaction at point A. 30 6 m Stop Water
The 18-ft-long gate of the figure below is a quarter circle and is hinged at H. Determine the horizontal force, P, required to hold the gate in place. Neglect friction at the hinge and the weight of the gate. Assumer- 5 ft. Water H Hinge Gate
A bicycle tire pump has a piston with area 0.44 inches squared. If a person exerts a force of 30 lb on the piston while inflating the tire, what pressure does this produce on the air in the pump? Give your answer in psi.
at the bottom of a container, which forms an angle A with the horizontal, is a cube of edge a, as shown in the figure, made of a material of density p. Determine the force with which the cube presses on the bottom, if a liquid of density p0 is poured into the container. The top edge of the cube is h from the surface of the liquid. There is no liquid between the bottom of the container and the cube. The atmospheric pressure is P and the acceleration of gravity g (neglect the thrust).
A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and water is poured in left and right side of tank respectively. Magnitude of horizontal force at centre that should be applied on cylinder so that it does not roll is (for unit length) kN. 64m Oil S=0.7 1.2 m Water S=1 0.7m
3. The uniform 20 Mg triangular gate is 1.5 m wide at B and is hinged at A. The gate rests on a smooth flat bed. Determine the height h for which the force at B is zero. 10 m S- 0.9 S = 0.8 h Water A 10 m 1.5 m 60°