AS k Using Mohr's circle method, Draw Mohr's circle Draw the direction of the state of stress block for principal plane and max shear Determine: a) Principal plane: OP = degree. b) Principal stress omax ksi, Omin ksi, c)Max shear plane: Os = degree. d) Max shear stress Tmax = ksi, corresponding normal stress a = ksi

AS k Using Mohr's circle method, Draw Mohr's circle Draw the direction of the state of stress block for principal plane and max shear Determine: a) Principal plane: OP = degree. b) Principal stress omax ksi, Omin ksi, c)Max shear plane: Os = degree. d) Max shear stress Tmax = ksi, corresponding normal stress a = ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) The state of stesss at a point in a body relative to the xyz coordinate system is: 2 3 -5 [o]= 3 2 kpsi 6. %3D -5 2 -4 a) Determine the principle stresses and the direction cosines corresponding to each principle stress. b) Draw the 3D Mohr's circles. c) Determine the maximum shear stress. d) Find the orientation of the plane containing the maximum shear stress relative to the original axis system 3) For the stress tensor in problem 2: a) Determine the normal and shear stress on a surface intersecting a plane defined by 3 points (0,0,0); (2,-1,3); (-2,0,1) b) Give the magnitudes of these stresses and the direction cosines defining their directions.
3) Solve the plane stress problem using two-element model to find displacements and stresses. 15 kN 30 mm E-70 GPa Thickness - 10 mm
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
Given: The infinitesimal “happy-little-cube™" with stresses shown. Determine: Draw Mohr's circle for the stress shown, label a) max and min principal stresses, b) max shear stress, c) center and d) plot the stress state shown on the circle 12 ksi Show all work. Do not calculate any angles! 6 ksi
The internal loadings at a section of the beam in (Eigure 1) are shown Figure 20 mm 100 mm 200 mm 20 mm 10 kNm 20 mm 10/12 60 kN 80 KN 500 N-m Determine the in-plane principal stresses at point C. Also compute the maximum in-plane shear stress at this point Express your answers, separated by commas, to three significant figures. VAZ Ivec 4 d Submit Provide Feedback T Wha Bequest Answer ? MPA, MPA, MPA
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
A plane stress state is given as follows (50MP in the bottom right corner denotes the shear component, and others denote the normal components). 1) Please draw the Mohr's circle of this plane stress state. Indicate the center of the circle, the radius of the circle, and the point that corresponds to x-plane (the normal of the plane is x axis) 2) Determine the principal stresses and directions of this stress state using Mohr's circle. 3) Draw the stress element to show maximum shear stress 71, T2, and the corresponding normal stress. 75 MPa 50 MPa 50 MPa
A round solid bar has a diameter of 30mm. A tensile force of 120kN is applied at the centroid of area . A) Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line[ANS : 170 MPa] B) The force in Q1 is re-applied to the same round solid bar but 5mm above the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line[ANS:+396, -56 MPa] HOW to answer part two I did not get the answer !!
For the state of plane stress, stress components are shown on the element in Figure Question 1: a) Draw Mohr's circle b) Determine the principal planes and the principal stresses c) The stress components exerted on the element obtained by rotating the given element counterclockwise through 30°. y| 60 MPa x 100 MPa 48 MPa
For the given state of stress of element A, strictly using Mohr's Circle perform the following: plane 1 1 plane 2 6 =40 MPa 30° plane 3 30° -20/3 МРа T=40 MPa plane 4 ...18.435° a) Draw its MOHRS circle b) Determine the principal stresses Op1= Op2= Op3= c) Determine the maximum shear stress Tmax= d) Determine the stresses on the horizontal & vertical planes OH= Oy= THV=
Rod AB is fixed at side A with a length of 500m and a diameter of 20m. On side B, the rod experiences a torque of 2kN-m a compressive force of 10KN and a transverse force of 12kN. a) Find the stress state at center point C. b) Draw mohrs circle for the stress state. (Be sure to include principal values, A, B, sigma1 and sigma2) T= d%=20m 250m ZKN-m IOKN 7. A, 500m I2KN
stress element x=21Mpa, y=11Mpa, xy=8, angle=50 degrees using the arithmetic method and Moore's circle 1) Find the main stresses, their directions, and be the maximum shear stresses ) Find the maximum and minimum stresses when rotating at the given angle in the positive direction