Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage ofgas under pressure of 2.2 MPa.a.Determine the value of the tangential stress in the tank wallDetermine the value of the longitudinal stress in the tank wallb.30 mmhelt hand

Answered: Image /qna-images/answer/9e08e8f6-2dc1-42de-bed5-094164427be9.jpg

an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used sure of 2.2 MPa. rmine the value of the tangential stress in the tank wall rmine the value of the longitudinal stress in the tank wall 30 mm holt head

an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used sure of 2.2 MPa. rmine the value of the tangential stress in the tank wall rmine the value of the longitudinal stress in the tank wall 30 mm holt head

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 10mm thick cylindrical steel tank has an outside diameter of 650 mm. It is subjected to an internal pressure of 2.8 MPa. Find the tangential stress on the tank.
use mhors circle a.What is the value of the minimum stress in psf? b.What is the value of the normal stress acting at the plane AB in psf? c.What is the value of the shear stress acting at the plane AB in psf?
3 - Given Young's modulus E, Poisson's ratio, and normal stress in the negative x-direction, what y is needed such that &y=0? X % MJ oy
The thin walled cylinder diameter whose diameter is 6.24 meters and thickness of 15mm. is subjected to external pressure of 2.47MPa and internal pressure of 4.32MPA. What is the longitudinal stress applied in the walls of the cylinders? Choose the nearest answer. (A) 257 MPa (в) 450 MPа 612 MPa (D) 193 MPa (E) 120 MPa
Complete solution please
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
2. A cylindrical pressure vessel is a fabrication from steel plating that fits to the following descriptions: Thickness = 25 mm Diameter = 500 mm Length = 2.5 m What maximum internal pressure can be applied if the longitudinal stress is limited to 160 MPa, and the circumferential stress to 80 MPa
answer pls in hand written solution
1
During the tensile test, experiment on a sample of mild steel, data represented in the figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, the reduced diameter (d;) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inches and final Gauge Length (L) is 2.625 inches. Answer the questions below: Us TR 70- 60 - Lo LyP *IR 50 - EL PL: proportimal limit EL Elastic limit UXP = 4pper yield point Lyp : Lower us : uiti mated streagth IR : Indicanteed Strengty Rupture TR: True strength Ruptue 40 AL or 8t P 30 **PL (proportimal limt) Direct strain E strain (in/in) aStress Iblinz (esi) 0.003. ogo o-200
A cylindrical tank with an inner diameter of 2.5 m and a wall thickness of 32 mm is made of a steel alloy and subjected to an internal pressure of 2.3 MPa. a) Determine the maximum hoop stress (in MPa). b) If the steel alloy has a yield stress of 350 MPa, what is the maximum allowable pressure if a factor of safety of 2.5 with respect to yield is required (in MPa). c) Determine the maximum longitudinal stress (in MPa). d) A pressure vessel is described as thin-walled when the ratio of the inside radius to the wall thickness is greater than or equal ________?
A solid steel bar 50 mm in diameter and 1.5 m long is secured between rigid walls. If the stress in the bar is zero at 27°C, what will be the stress (MPa) in the bar when the temperature rises to 42°C? Use E = 200 GPa and a = 12.5 × 10-6 m/m-°C. %3D